You can refine your search further by entering make and model number if you are looking for parts. If you are looking for tutorials please use appliance type only. If you need help please use FAQs or ask a question in contact us page.
Having trouble with layered Navigation? Watch Video
March 2, 2025 
Bosch WAE24368GB Washing Machine goes through full cycle to finish, but it is spinning very slow and washing still very wet.I have remove the drain which is clear. Could it be the control panel and have you got one. Thank you for your assistance in this matter.John
February 21, 2025
Bosch WAN28150GB washing machine very noisy when in use particularly when at increased revs.
I require a “Drum Bearing Kit” please.
January 8, 2025
Hi there, thanks for your video on YouTube regarding a teardown of a Bosch WAE24368GB washing machine. Having followed the process I have been able to confirm a broken spider on my 12+ year old machine. Given the cost to repair I have decided to buy a new machine. Do you have any recommendations on which machine to buy in terms of reliability/quality, etc. I have a budget of around £500, and would like 7-8kg capacity.
Also would you like any of the parts from the old machine (for free)? Am based near Milton Keynes if you are ever over this way.
Many thanks
Adam
January 8, 2025
We have a single parent mother and are trying to assist. She has the Siemens WM14P360GB washing machine that stopped functioning with an E43 fault which is listed as brushes.
I have replace the brushes though there was still some wear left on the old ones.
The motor will still not run in any wash selection.
It drains, fills, door opens and the timer at the end of a program still shows 1 min without a door opening and does not clear.
I do not have a test rig for the motor and have not been able to configure the wiring as yet and have found connection 3 to be for both brushes not individual brushes l and right,.
Can you advise
Thanks,
Robin
December 26, 2024
Beko WM5101W washing machine will fill, turn drum in both directions, heat water then continue to turn one way for 10 seconds (approx), pause for ten seconds, then turn the other way for ten seconds for as long as I care to let it. Up to 20 minutes before I give up waiting for a drain and refill, and press and hold ‘Cancel’. The machine immediately stops, runs the pump to empty the suds and lights ‘Spin/End’. Can you advise, please, why the machine will not follow through any wash program, and what a solution may be?
With thanks.
( I found you on YouTube and am a subscriber)
(
March 30, 2015
Important notice on Beko WM5100S WM5100WBefore entering test mode please be aware that you are not meant to leave the washing machine Unattended. There is a chance the machine can overfill when testing the water valves or the Machine could overheat when testing the heater. Also when entering the test mode make sure the
December 13, 2014
To order your Washing machine NTC Sensors and Elements you will need your full model number. (This is normally around the washing machine door frame on a sticker) The temperature is controlled by the PCB by means of a NTC temperature sensor incorporated in the heating element when you test it the Resistance drops as the
November 13, 2025
Dealing with a Bosch WAN28259GB washing machine that won’t drain or empty is one of the most common service calls we get. If your Bosch or Siemens washing machine is flashing the E36-10 error code (or the older E18 or E03 on classic models), it’s telling you one thing: washing machine couldn’t drain the water […]
October 31, 2025
In this guide, we’re focusing on the Beko WMC1282W washing machine. I’ll walk you through how to enter the machine’s diagnostic test mode and what all the error codes mean. This is the essential first step for correctly identifying any faults before you start a repair. The specific machine featured in our video had an […]
September 29, 2025
If your Indesit washing machine is not spinning, failing to drain, and flashing up error codes like F01, F02, or F05 you’re in the right place. These intermittent faults can be frustrating, but often they point to a single, very common, and affordable component failure: worn motor carbon brushes. This guide will walk you through […]
