NEW REPAIR GUIDES

FORGOT YOUR DETAILS?

AAH, WAIT, I REMEMBER NOW!

Beko washing machine self test & diagnostic mode

by / Monday, 27 July 2015 / Published in Washing machines

How to enter test mode Beko washing machine to find the fault

 

When looking at the dial on a Beko washing machine treat it as a clock 1 to 12 as in picture.
On some models you may have more programs but for the basic access into the diagnostic mode is the same the same

How to enter test mode Beko washing machine to find the fault

Start by turning the washing machine of with door shut.

Now turn the dial to the position 1 Which is normally the 90c hold the start /pause button down while you press the on/off button to on for a couple of seconds till light flashes

Now turn the dial to the position 6 and hold down a few seconds the next time you enter it should turn on all the lights now you are in self test diagnostic mode:

Every time you Press the on/off button it will change the test function.

1st all the lights will show

 2nd will not do anything

3rd This will tell the motor to turn at standard wash speed clockwise with pump emptying.

4th This will tell the motor to turn at standard wash speed anticlockwise with pump emptying.

5th This will tell the motor to spin clockwise with pump emptying.

6th This will activate right hand compartment water valve. Please note machine will keep filling until you stop it.

7th This will activate left hand compartment water valve. Please note machine will keep filling until you stop it.

8th This will activate booth water valves together. Please note machine will keep filling until you stop it.

9th will not do anything

10th this will start fill cycle until water activates the pressure switch at normal fill level (Normally just below the glass on the door) when the Beko washing machine has reached the level it will start clockwise rotation at normal wash action and heat the water. Please note You Have to stop it manually.

11 this will activate the pump only to empty.

Press again and you are back at the start. Turn machine of and leave for a few minutes and the switch back on and you’re in normal wash mode.




70 Responses to “Beko washing machine self test & diagnostic mode”

Newer Comments »
  1. Gary robinson says : Reply
    January 7, 2016 at 6:10 pm

    Carried out procedure as above however step 3 & 4 did indeed make the motor turn as described but at spin speed and when step 4 selected a flash was observed coming from the motor. Electrical flash due to change in direction at high speed I think. Any suggestions?

    My fault is that the washer will complete all cycles but will not spin even when spin only function selected. It will start up initially and then stop for a few minutes as though out of balance but I’ve been running it empty so it should spin with no issues.

    Any help/advice much appreciated.

    Gary

  2. Leanne mason. says : Reply
    March 7, 2016 at 11:50 pm

    I’ve got code 8364 on mine. Does everything on the self test right.
    It just stop when 3minutes into cycle. Is it possible it’s not heating the water? As the drum is full. It’s makes a clicking sound like the machine wants to move onto next step
    Thanks in advance
    Leanne

  3. baljeet says : Reply
    April 5, 2016 at 12:39 pm

    hi my beco machine’s door is stuck and its full of water and washing, please help

  4. Chris says : Reply
    January 31, 2017 at 10:10 am

    I have a beko washing machine it starts to fill on a wash cycle and then stops with a tap signal. Water is getting into the machine ive cleaned the filter. Ive taken the washing machine out and also done a diagnostic it doesn’t move the drum or do the spin it just goes straight to testing the valves and If you leave it the washing machine will over fill. I cant understand why it skips the turning of the drum part if the diagnostic

  5. Karen says : Reply
    April 8, 2017 at 11:45 am

    I have a beko wmb91442lw washing machine and when I do the self test it starts with filling with water then as I press the buttons it go see through the full testimonial and when it is finished it starts to fill with water again and when I switch it off and on again I only have 02:46 e on the panel. Can you help.
    Thanks Karen

  6. Terri says : Reply
    April 9, 2017 at 6:20 pm

    My beko washing machine is not changing programs when I turn the dial

  7. Terri says : Reply
    April 9, 2017 at 6:21 pm

    My beko washing machine does not change program when turning the dial

  8. Notable says : Reply
    April 19, 2017 at 2:26 am

    I have an additional question that won’t be answered

  9. Michael Bulger says : Reply
    April 19, 2017 at 5:53 pm

    Do you know how to put a beko wm74155w washing machine into test mode. Thanks

  10. Calvin Broadhurst says : Reply
    May 7, 2017 at 3:42 am

    Can you please tell me how to put the Beko WMY 9048 in to diagnostic/test mode?

  11. Steve Schofield says : Reply
    May 14, 2017 at 4:28 am

    I have a Beko wmb751441la during the test mode at the start F13 comes up and when I try and go through the test mode as you described it doesnt do what you described.
    So what is Fault 13 please

  12. Nikki Clark says : Reply
    June 3, 2017 at 4:41 pm

    I have a Beko81445LW. Have done a test mode as per the instructions given. The water is ok and the machine is draining away ok but then keeps trying to drain and the spin cycle doesn’t seem to want to kick in. Any suggetions as to why, where the problem might be and how to fix it. Thank you.

  13. Glenn says : Reply
    June 24, 2017 at 7:51 pm

    Hi i have a beko WM5120S i have checked for fault codes and found the first LED in the row flashing 2nd and 3 LED are lit constant. When start button pressed the machine will the trip the RCD After approx 3seconds.
    The machine do all the functions in the test sequences ok.

    Any thoughts??
    Thanks in advance.

  14. esti says : Reply
    July 15, 2017 at 10:04 pm

    beko 91440 dosent seem to start. I turn dial, set programme, it beeps as if starting but doesn’t fill with water

  15. Michaela says : Reply
    September 9, 2017 at 4:47 pm

    I have a Beko WMB81241LW washing machine, the door won’t open. Any ideas?

  16. Jesse says : Reply
    October 3, 2017 at 3:08 pm

    I have a beko WMB61432B 1400rpm 6kg washing machine, it does not appear to be filling with water, I suspect the water inlet valves are not working.
    What would be the best way to check these?
    Anyone have any other suggestions.

  17. joe says : Reply
    October 19, 2017 at 9:24 pm

    hi I have a beko wy104674mw washing machine everything works apart from the drum it doesn’t turn at all
    I would like to run diagnostic which button to press ? thanks

  18. Alex Holden says : Reply
    November 8, 2017 at 9:06 am

    Hi
    When I switch my Beko washing machine on the lights flash and looks like it’s ready to wash. But there is no further action, no water noise from the pump and movement of the drum. I’ve just got lights on??
    Not sure what’s up with this.

  19. John says : Reply
    February 8, 2018 at 7:58 pm

    Hi, I have a beko WMB 81241 LS and it seems stuck on a program.
    I recently moved the machine into my new house, and once plumbed in it failed to work.

    I tried the test by turning off and holding down start to get the error code of E18. This is since cleared and I am now getting a code of 1540.. nothing else.

    I have checked the filter and it is all clear, I have also checked the wiring going into the PCB and all seems fine.

    Can anyone help?

  20. Joanne says : Reply
    February 20, 2018 at 1:11 pm

    My electric tripped and now my beko wm6112w won’t work properly how do I reset it?

Newer Comments »
24h technical help answers

Questions on faults in the comments will not be answered. Please use the contact us form instead.

TOP