Beko washing machine wmb 7, 8, 9 Series diagnostic & test mode

by / Tuesday, 10 May 2016 / Published in Washing machines, Water Systems & Valves

How to enter test mode on Beko wmb 7, 8, 9 Series washing machines diagnostic & test mode to repair faults and test errors

Beko Diagnostic

 Important notice on Beko 

Before entering test mode please be aware that you are not meant to leave the washing machine Unattended. There is a chance the machine can overfill when testing the water valves or the Machine could overheat when testing the heater. Also when entering the test mode make sure the drum is empty as not to cause damage when on spin mode:

This video can be used on all these makes

WMB81431LW, WMB71231B, WMB61631W, WM5141W, WM5141S, WMB71422S, WMP601W, WMP541W, WMB81241LS, WML72S, WASH814DW, WMC6100W, WMB61021W, WMB71642S, WMB61431W, WMC6140W, WMB71021W, WMB61631S, WMB81241LB, WML72B, WMP652W, WMP631S, WM74135W, WMB61221S, WMB71231S, WM74155LW, WM74155LS, WMB61431S, WMB51221W, WM622W, WMB61431B, WMD61W, WMB51221S, WMP501S, WMB61221W, WM7355S, WMB81221LS, WMC6100S, WMB81241LW, WML72WXC, WMC6120W, WMB91242LB, WML15105D, WM5100W, WME8227W, WMB71442W, WM85135LW, WME7227W, WME7247W, WM5100S, WMC62W, WM6123W, WME7267W, WMC61W, WM6103W, WM6123S, WME7227S, WM6167W, WME8227S, WM5121W, WM6111W, WMP621W, WM612W, WM6355W, WME7247S, WMC61S, WM5121S, WM6167S, WME7267S, WM7335W, WME8227B, WMB91242LC, WMI71641, WMI7462, WMI71441, WMB71231W, WME7227B

Test Mode Sequence

If you have problems with the drum not turning or spinning. Then check the carbon brushes in the motor first and test the motor separately before running this Diagnostic sequence as you could do damage to the PCB.

 

To enter test mode.

 It is advisable that washing machine be switched off or at least 5 minutes prior to entering test mode

With the machine switched off shut the door and turn the dial to the 12 o'clock position. Now press and hold down the start/pause button and press the on/off on, while holding the start/pause button down for 3 seconds until the display shows a number or error code.

  Now that you've entered the Diagnostic / test mode, remember every time you press the start/pause button this will be one advance the program to a new test.

  • 1: All the the display or led’s will flash to check that they are working and door will now be locked.
  • 2: Drum does a clockwise rotation.
  • 3: Drum rotates anticlockwise rotation 
  • 4: Goes into spin mode on clockwise rotation make sure there are no clothes in machine before performing this test as washer will spin at its fastest rpm. 
  • 5: right hand water valve check
  • 6: left hand water valve check
  • 7: both water valve are now activated and all 3 compartments will have water flowing in. 
  • 6: This is the full wash and heat test. Machine will start to fill to the correct water level and continue to heat and wash.
  • 7: the machine will empty. the pump should drain the water away.
  • 8:After it has finished turn the machine off and on this will go back to normal mode.

 

entering test mode one beko washing machines

Tap symbol showing as fault

Beko washing machine error Diagnostic fault codes

Turn dial to 12 o'clock position

Beko washing machine E08 Error code

Error code showing fault

beko washing machine fault codes and error codes

Display will flash when in test mode




Tagged under: , ,

125 Responses to “Beko washing machine wmb 7, 8, 9 Series diagnostic & test mode”

  1. Phil says : Reply

    Hi
    I changed the door seal on my Beko wmb71642w as per your video no problem but switched it on I can’t select a program or get in test mode any ideas

    Thanks

  2. U says : Reply

    Hi I have Beko WX742430B . And due to the on/ off switch being on the selector dial I can’t carry out the self diagnose, is there another way of doing this on the machine , the machine starts a cycle and then stops after a few seconds , the bushes on the machine were down to nothing so replaced them and now suspect that the pcb is broken , any help you can give will be greatly appreciate

  3. Philip mc Goldrick says : Reply

    Hi i have a beko wtb841r2w that is tripping the rcd ,it can trip it right at the start of the cycle or at any stage during the cycle.

    • This can be many things bad wiring touching the casing, a motor fault or an element braking down without having the machine in front of me it a hard one for me to help on

  4. Barry Johnstone says : Reply

    Hi i got a error code e2 and on step 7 it does nothing on self diagnostic….thanks for any help

  5. David Pearce says : Reply

    Hello my beko wmb 71442 s is displaying e 18 I try to enter test mode and it will not allow me to do anything at all thanks

  6. Steve Fudgell says : Reply

    We have a Beko WME 8227W and suddenly when we are unable to use it. On the main dial the only display that shows details is the Daily Quick one, but even that will not start. All other cycles have no details displayed. Tried pressing & holding Start/Pause/Cancel button for 5 seconds to reset but it made no difference. Also Cleared out some debris in the Filter but still unresponsive. Watched your YouTube video and entered Diagnostic & Testing mode ok, which display a number 8365. When releasing the button the full display illuminates as in your video, but start does not start the Testing Sequence. In fact no button will start the sequence, nothing happens whatsoever.

  7. Sami says : Reply

    Hello technician

    My Beko WM95145LW it’s Woking fine but it’s not heating the water I have replaced the heating element comes with thermistor, Still the machine not heating the water, I did do some checks and I see that the neutral is missing , can you please help or if you can tell me how can I get the schematic diagram for this machine ,
    Kind Regards
    Sami

  8. Mark Hopkins says : Reply

    Please help. I have Beko wash m/c WMB 71442 W.
    Has stopped running & I have gone through diagnostic mode.
    1) Clockwise test rotation very jumpy reluctant to run fast. Like a small pulse every other second. Does not pick up proper speed.
    2) Anticlockwise test similar to above.

    Motor picks up well to speed later in drying tests both directions.

    But the machine will not even start to run when selecting normal wash or spin cycles.

    Please help.
    Cheers.

  9. José Ramos says : Reply

    I have the Beko WMB 91442 LC. The door handle, that opens the latch, broke and I installed a new one. It wouldn’t start a program, but from the first try to start a program it was stuck at that program. I disconnected from the plug for a day and when I turned it on it kept that block. Tried the Child Lock on and off and it stayed the same. I ran the test mode nd understood that it did not lock the door. I checked the new handle and it had a small section that didn’t let the latch go flush against the door. I took it out, carved the the section from the plastic handle and installed again. Turned on the machine, waited and it started working fine.
    So, if anyone changes anything on de door, or the door latch, and it starts giving problems, check if the latch is flush to the ride and connecting as it should in the door lock.

  10. Paul Molyneaux says : Reply

    Hi Paul,
    First I’d just like to say what an absolute star you. Thankyou so much for sharing your wisdom.
    I have an issue with my Beko 7 .I have ran the diagnostic program to your instructions. I’ve unplugged waiting 5 mins( plus) and repeated diagnostics × 5 times .
    First I get a number 1540
    Test 1 to 7 all fuction .
    On test 8 the water fills drum to required level . Then nothing for a few seconds .Then the Diagnostics display flicks to the display usually associated with the cotton setting (12 oclock) display Awaiting for me to press start . I turn off machine .unplug. wait .Then plug and turn machine on after turning dial to centrafuge and pump setting (6 o’clock ) And pump out water . This also appears stuck as it pumps and does nothing and the time display if 12 mins cycle never changes .
    Can you please give me any insight into what the problem may be and where to check next .
    With sincere gratitute
    Paul Molyneaux

  11. joe says : Reply

    Hi there, Eco WMB washer 81445l LW, not spinning at all, I removed motor, cannot see any brushes at all, pump is clear and machine drains ok. There is a line across the tap logo on the diagnostic window ????. Skips to water valve checks without spinning cycle, on diagnostic mode. Can you help please. Cheers Joe.

  12. Annunciata. O Omoregie says : Reply

    Hi my beko is WMB 714422 W
    I got the error code 08 but when I press the start button it started no sequence whatsoever. what do I do?

  13. Kyra says : Reply

    My machine WMI 71641 is not responding. I cannot select any program. I have tried to hold the reset button for 3 secs, it is flashing. I have unplugged from the mains and switched it back on. It is still not allowing me to select any program. Any help is much appreciated.

  14. Simone lazarus says : Reply

    My beko washing machine is not working. The lcd display is on but the lights to the right do not work. Normally the door lock button light is red and then the wash light goes on etc etc. Now when i turn the dial to any setting and press start i get the child lock countdown and then child lock on and then child lock off. The machine is less than 1 year old

  15. Tim Staies says : Reply

    Hi Paul,

    Model : Beko WMB91242LC XL9

    I’ve changed the brushes on the motor as per your video, but now have a number 15 16 showing on the screen before it enters test mode, and the drum still won’t turn at all. Any ideas please?

    Many thanks in advance,
    Tim

24h technical help answers

Leave a Reply to José Ramos

TOP