Beko washing machine wmb 7, 8, 9 Series diagnostic & test mode

by / Tuesday, 10 May 2016 / Published in Washing machines, Water Systems & Valves

How to enter test mode on Beko wmb 7, 8, 9 Series washing machines diagnostic & test mode to repair faults and test errors

Beko Diagnostic

 Important notice on Beko 

Before entering test mode please be aware that you are not meant to leave the washing machine Unattended. There is a chance the machine can overfill when testing the water valves or the Machine could overheat when testing the heater. Also when entering the test mode make sure the drum is empty as not to cause damage when on spin mode:

This video can be used on all these makes

WMB81431LW, WMB71231B, WMB61631W, WM5141W, WM5141S, WMB71422S, WMP601W, WMP541W, WMB81241LS, WML72S, WASH814DW, WMC6100W, WMB61021W, WMB71642S, WMB61431W, WMC6140W, WMB71021W, WMB61631S, WMB81241LB, WML72B, WMP652W, WMP631S, WM74135W, WMB61221S, WMB71231S, WM74155LW, WM74155LS, WMB61431S, WMB51221W, WM622W, WMB61431B, WMD61W, WMB51221S, WMP501S, WMB61221W, WM7355S, WMB81221LS, WMC6100S, WMB81241LW, WML72WXC, WMC6120W, WMB91242LB, WML15105D, WM5100W, WME8227W, WMB71442W, WM85135LW, WME7227W, WME7247W, WM5100S, WMC62W, WM6123W, WME7267W, WMC61W, WM6103W, WM6123S, WME7227S, WM6167W, WME8227S, WM5121W, WM6111W, WMP621W, WM612W, WM6355W, WME7247S, WMC61S, WM5121S, WM6167S, WME7267S, WM7335W, WME8227B, WMB91242LC, WMI71641, WMI7462, WMI71441, WMB71231W, WME7227B

Test Mode Sequence

If you have problems with the drum not turning or spinning. Then check the carbon brushes in the motor first and test the motor separately before running this Diagnostic sequence as you could do damage to the PCB.

 

To enter test mode.

 It is advisable that washing machine be switched off or at least 5 minutes prior to entering test mode

With the machine switched off shut the door and turn the dial to the 12 o'clock position. Now press and hold down the start/pause button and press the on/off on, while holding the start/pause button down for 3 seconds until the display shows a number or error code.

  Now that you've entered the Diagnostic / test mode, remember every time you press the start/pause button this will be one advance the program to a new test.

  • 1: All the the display or led’s will flash to check that they are working and door will now be locked.
  • 2: Drum does a clockwise rotation.
  • 3: Drum rotates anticlockwise rotation 
  • 4: Goes into spin mode on clockwise rotation make sure there are no clothes in machine before performing this test as washer will spin at its fastest rpm. 
  • 5: right hand water valve check
  • 6: left hand water valve check
  • 7: both water valve are now activated and all 3 compartments will have water flowing in. 
  • 6: This is the full wash and heat test. Machine will start to fill to the correct water level and continue to heat and wash.
  • 7: the machine will empty. the pump should drain the water away.
  • 8:After it has finished turn the machine off and on this will go back to normal mode.

 

entering test mode one beko washing machines

Tap symbol showing as fault

Beko washing machine error Diagnostic fault codes

Turn dial to 12 o'clock position

Beko washing machine E08 Error code

Error code showing fault

beko washing machine fault codes and error codes

Display will flash when in test mode




Tagged under: , ,

134 Responses to “Beko washing machine wmb 7, 8, 9 Series diagnostic & test mode”

  1. Stu says : Reply

    Hi, Wmb71543w has an f11 code on diagnostic initialization, nothing else happens after that.
    I’d like to know what code F11 stands for please?

    • F11 is not an error code on this model, but there is an error code e-11. This means that you have a motor fault on your Wmb71543w I suggest you test the motor and also the circuit board supplies the motor

  2. Trish says : Reply

    Hi,

    My Beko WMB 71442S display screen constantly flashes and will not allow me to select the correct washing functions. If I whack it a few times it eventually stops flashing.

    When I put the machine in diagnostic mode for the first time, I got the E18 code however, this is no longer appearing. Also, the diagnostic stage which fills the drum with water and tester the heater does not complete and the machine automatically switches back to normal mode after a few minutes.

    Can you kindly advise?

24h technical help answers
TOP