Beko washing machine wmb 7, 8, 9 Series diagnostic & test mode
Beko Diagnostic
Important notice on Beko
Before entering test mode please be aware that you are not meant to leave the washing machine Unattended. There is a chance the machine can overfill when testing the water valves or the Machine could overheat when testing the heater. Also when entering the test mode make sure the drum is empty as not to cause damage when on spin mode:
Tap symbol showing as fault
Turn dial to 12 o'clock position
Error code showing fault
Display will flash when in test mode
134 Responses to “Beko washing machine wmb 7, 8, 9 Series diagnostic & test mode”
Hi
How do I carry out a self test mode on a Beko WMB71233W
Thanks Dave
I’ve had code F13 on Beko WMB 81641 LC
I’ve tried doing the self diagnostic test. My washer skips the spin part but does all the rest.
When I turn it on normally to try and test it starts to fill and then drains and just keeps doing this, doesn’t go any further, any ideas before expensive repair from beko
Machine won’t do any thing stuck with the softener symbol and 00:16 tried all the resets and won’t do anything won’t even do a function test
Hi ive done the diagnostic test it shows 15 10 . It will not drain and makes a slight humming noisen .
Hi my Beko wmb is showing e03 could u plz help me on what this could be plz
Thank you
Doesn’t work at all so no help what so ever I hate shit that says this that nd the other nd still doesn’t come in handy at all fucking bullshit
My Beko WMC126W stopped spinning, looked in and belt was broke. Got new belt and replaced it (though having trouble keeping it on) and started to wash. Everything fine first spin, second started to squeal and then stopped spinning, and won’t spin. Would that be the brushes now and how can you check without removing the motor? I’d appreciate any help that can be suggested, thank you
hi there
i have washing machine wml51021 i have issue for quick wash i dont know how to quick wash if anyone know please let me know how to wash quick wash
thank you
Error e08 my machine does do anything the display does not show the tap..I have replaced the water valve an still nothing??? Numbers 01:23 on display also “e” an the start sign “>” is flashing…iv checked all the obvious????? Any advice please would be appreciated
Hi
Thank so much for your help
I have BEKO D7102 SE, after putting it into a test mode
After first pressing the START/Pause SW= 1- All light blink
After 2nd press, NOTHING HAPPEN !
Beko Model no WMB 71442S. Not working and on test mode as per your vedio, shown error no E 07 and doesn’t continue test mode.
Our WM74155LW does not have a start button, just the rotary switch. How do put it into test mode please?
BEKO Model WMB751441 LA the washing machine .. Blinking ..END message with a locked symbol how do we get rid of the message and start a new load again thanks
WMB79127 ERROR E17 WHAT DOES IT MEAN?
Beko WMB81241LB Main control module had blown components and burnt circuit board, DC control module did not look good. Fitted replacement main control module and DC control module. The machine would not start on any programme, the start indicator flashes continuously. the only thing that happens when the start/pause/cancel button is pressed is the degrees C indicator flashes off/on momentarily. holding the button in for 3-5 seconds changes the display to 0.00 from 0.39 with the start indicator flashing. during this time the door is locked but nothing else happens.
On entering Diagnostic/test Mode the display indicates error code E17 on releasing the start/pause/cancel button the display indicates all symbols, on pressing the start/pause/cancel button the display does not go into flashing mode but continues to be on steady, further pressing of the start/pause/cancel button does nothing at all. during this time the door is not locked.
I have checked the solenoid coils of the water valves and they both give a reading of approximately 3.5 K ohms.
I would appreciate any help you could give me to rectify this problem, i.e what to check for, or items to test/replace.
Kind Regards:- S.Burrows
Hi there,
Our Beko washing maschine WMB 71443 LE shows fault Code 0428. What does it mean please?
Best regards
Thorsten
Hi I’ve got a wmb71231b cannot do a test as not got on/off button only a start button on front of wash machine so unable to do test plz help thankyou washer not turning , brushes were new 9 months ago thankyou
Your site and it’s videos are very useful and have solved a problem with our Beko machine, I will be recommending you to my friends.
Thanks.
I’m glad we could help please remember to support the website by shopping with us, and if we really helped you can always donate by pressing the Buy paul a Beer page
My Beko wm91535lb does not enter the diagnostic sequence at all. I initially get 04 17 appear on the screen then all the feature lights, when I press the start button to go through each test nothing happens
hi the led lights are flashing for test mode but nothings happening