Beko washing machine wmb 7, 8, 9 Series diagnostic & test mode
Beko Diagnostic
Important notice on Beko
Before entering test mode please be aware that you are not meant to leave the washing machine Unattended. There is a chance the machine can overfill when testing the water valves or the Machine could overheat when testing the heater. Also when entering the test mode make sure the drum is empty as not to cause damage when on spin mode:
Tap symbol showing as fault
Turn dial to 12 o'clock position
Error code showing fault
Display will flash when in test mode
134 Responses to “Beko washing machine wmb 7, 8, 9 Series diagnostic & test mode”
Hi
I changed the door seal on my Beko wmb71642w as per your video no problem but switched it on I can’t select a program or get in test mode any ideas
Thanks
Same as above
Hi I have Beko WX742430B . And due to the on/ off switch being on the selector dial I can’t carry out the self diagnose, is there another way of doing this on the machine , the machine starts a cycle and then stops after a few seconds , the bushes on the machine were down to nothing so replaced them and now suspect that the pcb is broken , any help you can give will be greatly appreciate
Hi i have a beko wtb841r2w that is tripping the rcd ,it can trip it right at the start of the cycle or at any stage during the cycle.
This can be many things bad wiring touching the casing, a motor fault or an element braking down without having the machine in front of me it a hard one for me to help on
Hi i got a error code e2 and on step 7 it does nothing on self diagnostic….thanks for any help
To have any question answered you must use the contact us page
Hello my beko wmb 71442 s is displaying e 18 I try to enter test mode and it will not allow me to do anything at all thanks
We have a Beko WME 8227W and suddenly when we are unable to use it. On the main dial the only display that shows details is the Daily Quick one, but even that will not start. All other cycles have no details displayed. Tried pressing & holding Start/Pause/Cancel button for 5 seconds to reset but it made no difference. Also Cleared out some debris in the Filter but still unresponsive. Watched your YouTube video and entered Diagnostic & Testing mode ok, which display a number 8365. When releasing the button the full display illuminates as in your video, but start does not start the Testing Sequence. In fact no button will start the sequence, nothing happens whatsoever.
Hello technician
My Beko WM95145LW it’s Woking fine but it’s not heating the water I have replaced the heating element comes with thermistor, Still the machine not heating the water, I did do some checks and I see that the neutral is missing , can you please help or if you can tell me how can I get the schematic diagram for this machine ,
Kind Regards
Sami
Please help. I have Beko wash m/c WMB 71442 W.
Has stopped running & I have gone through diagnostic mode.
1) Clockwise test rotation very jumpy reluctant to run fast. Like a small pulse every other second. Does not pick up proper speed.
2) Anticlockwise test similar to above.
Motor picks up well to speed later in drying tests both directions.
But the machine will not even start to run when selecting normal wash or spin cycles.
Please help.
Cheers.
I have the Beko WMB 91442 LC. The door handle, that opens the latch, broke and I installed a new one. It wouldn’t start a program, but from the first try to start a program it was stuck at that program. I disconnected from the plug for a day and when I turned it on it kept that block. Tried the Child Lock on and off and it stayed the same. I ran the test mode nd understood that it did not lock the door. I checked the new handle and it had a small section that didn’t let the latch go flush against the door. I took it out, carved the the section from the plastic handle and installed again. Turned on the machine, waited and it started working fine.
So, if anyone changes anything on de door, or the door latch, and it starts giving problems, check if the latch is flush to the ride and connecting as it should in the door lock.
Hi Paul,
First I’d just like to say what an absolute star you. Thankyou so much for sharing your wisdom.
I have an issue with my Beko 7 .I have ran the diagnostic program to your instructions. I’ve unplugged waiting 5 mins( plus) and repeated diagnostics × 5 times .
First I get a number 1540
Test 1 to 7 all fuction .
On test 8 the water fills drum to required level . Then nothing for a few seconds .Then the Diagnostics display flicks to the display usually associated with the cotton setting (12 oclock) display Awaiting for me to press start . I turn off machine .unplug. wait .Then plug and turn machine on after turning dial to centrafuge and pump setting (6 o’clock ) And pump out water . This also appears stuck as it pumps and does nothing and the time display if 12 mins cycle never changes .
Can you please give me any insight into what the problem may be and where to check next .
With sincere gratitute
Paul Molyneaux
Hi there, Eco WMB washer 81445l LW, not spinning at all, I removed motor, cannot see any brushes at all, pump is clear and machine drains ok. There is a line across the tap logo on the diagnostic window ????. Skips to water valve checks without spinning cycle, on diagnostic mode. Can you help please. Cheers Joe.
Hi my beko is WMB 714422 W
I got the error code 08 but when I press the start button it started no sequence whatsoever. what do I do?
My machine WMI 71641 is not responding. I cannot select any program. I have tried to hold the reset button for 3 secs, it is flashing. I have unplugged from the mains and switched it back on. It is still not allowing me to select any program. Any help is much appreciated.
My beko washing machine is not working. The lcd display is on but the lights to the right do not work. Normally the door lock button light is red and then the wash light goes on etc etc. Now when i turn the dial to any setting and press start i get the child lock countdown and then child lock on and then child lock off. The machine is less than 1 year old
Hi Paul,
Model : Beko WMB91242LC XL9
I’ve changed the brushes on the motor as per your video, but now have a number 15 16 showing on the screen before it enters test mode, and the drum still won’t turn at all. Any ideas please?
Many thanks in advance,
Tim
Hello, My Beko WTG741M1W has E11 Code, any advise would be much appreciated
I tried putting it through the test mode but none of the cycles worked
Many Thanks
Liam
Hi, I’ve replaced the heater element on my Beko WM7023W, but it is still not heating. When i get to the fill and heat section of the diagnostics, it doesn’t heat and comes out of diagnostics to the wash programme screen, leaving water in the drum.
Is there a way of ‘resetting’ the appliance so it recognises the new element?
Error: 0428
Model: WMB 71443 LE
I got this error 0428 the second time now and it seems that it has something to do with the door. I don‘t know if it can be repaired by myself but I found a workaround for me: slamming the door shut.
This doesn‘t always work on the first try. I sometimes wait for a bit then try it again, shutting the door fast and with force. I know it has worked, when I press the start button and the diagnosis test begins (or the chosen washing program). I then let it run a diagnosis cycle before turning it off and on again. And pray that the next door error 0428 is way in the future and the door (or whichever part is responsible for that error) will last a few more years.
Thanks a lot for the very good instructions and screenshots – the order of the test phases/modes is a bit different with my model, but it helped a lot.
I have a beko eco WMB81445 LW I can put it in diagnostic mode but then it won’t let me go any further. Any suggestions greatly received
Hi there, WMB91442 LW washer not spinning at all, I removed motor, cannot see any brushes at all, pump is clear and machine drains ok. There is a line across the tap logo on the diagnostic window ????. Skips to water valve checks without spinning cycle, on diagnostic mode. Can you help please. Cheers Henry