How to enter test mode on Whirlpool AWO/D & AWD Series Repair Faults & Test Errors
Whirlpool Washing Machine Error Fault Codes – FOO, FH, FA, FP, F5, F6, F7, F8, F9, F10, F11, F12, F13, F14, F15, F16, F18, F20, F21, F22, FDL, FDU
This video will show you how to enter your Whirlpool Washing Machine into test mode and diagnose the fault codes on AWO/D & AWD Series and general Whirlpool washing machines that may not relate to models sold outside Europe, especially models sold in the USA.
We are working on a Whirlpool, but this video is also good for Bauknecht, Fisher & Paykel, Ignis, Ikea, Laden, Maytag, Neutral & Philips models of washing machine.
How to Enter Test Mode Sequence
To enter the diagnostic/test mode sequence, you need to turn the dial to the DRAIN position, which is at eleven o´clock; then you must press the RESET button four times, within five seconds to enter the test mode sequence. (See video on this)
NOTE: this doesn´t always go in first time, so as soon as you turn the dial from the OFF position to the DRAIN position, you have 5 seconds to press the RESET button 4 times.
Once the machine as entered the test mode sequence you will see a series of flashing lights:
1 - The machine starts by checking if the door lock is working correctly;
2 - Then goes to a fill sequence where it will test each water valve individually – it will start filling the right hand compartment in the soap drawer, then switches over to the other water valve on the left hand compartment, after this, both water valves will be activated (fills all three compartments, including the fabric conditioner in the middle);
3 - Next it will test right hand rotation of the motor (clockwise), and left hand rotation of the motor (anticlockwise), while it´s also testing the NTC sensor and the heater element;
4 - The machine goes into empty cycle;
5 -Full test on the motor at maximum RPM
To Exit Test Mode
The machine will automatically exit the diagnostic/test mode sequence
After the test sequence if you find that you do need a part for your washing machine, you will need the full model number of the ID Plate, which you can normally find on the inside of the door frame or in the rear of the machine.
Sometimes you will need the 12 digit number, which is usually prefixed with 12NC in front of it, on some parts you will need both of these numbers, it might not be listed on the website because it is serial number dependent. (see picture on the left)
Whirlpool AWO/D & AWD Series Washing Machine Fault Codes
F00 - Drain pump triac failure
- Check drainage pump or possible PCB failure
- Check drainage pump
- Check wiring
FH - No incoming water detected
- Check water supply and hose
- Check water valves
- Check pressure switch
FA - Aquastop failure
- Check Aquastop switch
FP - Failure to drain
- Check drainage pump filter for blockages
- Check blockage in the drain hose in waste system
- Check drainage pump
- Check pressure switch
F5 - NTC Sensor (thermistor) failure
- Check thermistor (NTC)
- Check the wirings to thermistor and the PCB
F6 - Motor tacho not detected, no motor action
- Check motor tachometer
- Check wiring and connections to the motor and PCB
- Check motor carbon brushes
F7 - Triac short circuit
- Check electronic module
F8 - Heating element open circuit
- Check continuity on heating element
- Check relay (if fitted)
- Check heating element wiring to PCB
F9 - Overflow
- Check the amount of detergent being used to ensure that there has been no excessive foam
- Check pressure chamber
- Check pressure switch
- Check wiring to pressure sensor
F10 - Motor control unit or motor thermal safety operated
- Check connections to circuit board (PCB)
- Check motor thermal cut out
F11 - Communications error
- Check wiring between boards where more than one is fitted
- Check electronic control units (PCB)
F12- Heater element short circuit
- Check water heating element
- Check relay if fitted
- Check wiring to heating element and PCB connection
F13 - Dispenser circuit fault- normally door lock related
- Check door interlock
- Check wiring to door interlock and PCB connection
F14- EEPROM failure
- Check electronic module (PCB)
Whirlpool EU Washing Machine Fault Codes
FH - No incoming water detected
- Check water supply
- Check water valves
- Check pressure switch
FA - Aquastop failure
- Check Aquastop switch
FP- Failure to drain
- Check drainage pump filter for blockages
- Check blockage in the drain hose in waste system
- Check drainage pump
- Check pressure switch
F05 - NTC Sensor (thermistor) failure
- Check thermistor (NTC)
- Check the wirings to thermistor and the PCB
F06- Motor tacho not detected, no movement on the drum
- Check motor tachometer
- Check wiring and connections to the motor and PCB
- Check motor carbon brushes
F07 - Triac short circuit
- Check electronic module
F08 - Heating element open circuit
- Check continuity on heating element
- Check relay (if fitted)
- Check heating element wiring to PCB
F09 - Overflow
- Check the amount of detergent being used to ensure that there has been no excessive foam
- Check pressure chamber
- Check pressure switch
- Check wiring to pressure sensor
F10 - Motor control unit or motor thermal safety operated
- Check connections to circuit board (PCB)
- Check motor thermal cut out
F11 - Communications error
- Check wiring between boards where more than one is fitted
- Check electronic control units (PCB)
F12- Heater element short circuit
- Check water heating element
- Check relay if fitted
- Check wiring to heating element and PCB connection
F13 - Dispenser circuit fault- normally door lock related
- Check door interlock
- Check wiring to door interlock and PCB connection
F14- EEPROM failure
- Check electronic module (PCB)
F15 - Motor control unit error
- Check electronic module (PCB)
F16 - Controller failure
- Check electronic module (PCB)
F18 - Controller failure
- Check electronic module (PCB)
F20 - Controller failure
- Main Check electronic module (PCB)
F21 - Controller failure
- Check electronic module (PCB)
F22 - Controller failure
- Check electronic module (PCB)
FDL - Door lock error
- Check door interlock
- Check wiring to door interlock and PCB connection
FDU - Door unlock error
- Check door interlock
- Check wiring to door interlock and PCB connection
Hi
I have an AWO 3761. If I try to switch it on it trips the mains fuse! I have had a good look round after removing the top plate to see anything burnt out, but all looks clean! I don’t have a circuit diagram or a service manual to trouble shoot the problem. I have tried to see if there is any obvious short on Live-Neutral, as power cable enters the machine via a mains filter(?) – the DC resistance reads 920 ohms, but I don’t know if this is normal; I can trace it back all the way to what I suppose is the controller. Any suggestions what I should look for to isolate the fault?
hi we have on whirlpool AWOC7129p washer now when i try to switch on its indicates only the green indicator even the door not getting lock but its not showing service indicator display is on and its showing some duration of washing and temperature so kindly tell me what can be the fault
[…] How to enter test mode on Whirlpool AWO/D & AWD Series Repair Faults & Test Errors […]
Fantastic thankyou Paul xx
Whirlpool washing machine AWO/D 6100 is now completely dead, no lights anywhere. First load Worked perfectly, second load started ok and then everything stopped NO POWER LIGTHS. PS I checkekd that there is power going to the machine.
Any ideas I could try?
John
My whirlpool (AWO/D 6129 – 8592 987 18000) stopped midway through a wash cycle. It had no lights on at all. I emptied it of washing and drained the water. I checked the filter – OK. I checked the pump was free to rotate – OK. I checked the water entry filter – OK. I checked the wash drawer – OK. I cannot perform a test mode sequence because I cannot get any lights on the control console.
Have you any idea what has failed?
Hi everybody,
This is a general reply on the fault : ” machine dead, no leds blinking on the machine”
I just repaired a Whirlpool AWO4461 which was completely dead , and I first checked if power reached the main control board which is situated behind the front operating panel ; this was ok , so I cut off the power and removed the main control board ( I made lose all connectors first) opened the cover and I quickly saw that there were some electronic components burned (R020 =27ohms, and L003= 0.47mH) and also the IC = LNK304PN.
So I replaced these components as well as two capacitors 4.7uF/400 v and when I gave power to the module, the leds started blinking (I had turned the program knob (cental on the board) for one step so the board got power) and everything was back ok !
So that’s the solution : repair the main board , on the internet there is a repairkit available containing thes components.
success !
Walter from Belgium.
thanks a lot! seems to be the problem in my case too 🙂
I’m glad we could help please remember to support the website by shopping with us, and if we really helped you can always donate by pressing the Buy paul a Beer page
Hi
I have Whirlpool AWO/D 7314
My machine is showing fault F 22
Can you tell me what that means,
Hi
Some one can help to reconnect th electrical board panel
There are son many wire and I don’t know how to connect all of them properly
Thank you
nicola.difranco@gmail.com
My Whirlpool AW0/D 050 ‘Clean Pump’ light is ON. I have replaced the pump but the problem persists. HELP.
I have a whril Pool Top Load Washing machine 6.2 kg. It shows PE error. How to rectify it ? please answer. The technician has several time checked the Board, changed both valves but the problem is not solved.
Paul
I have a Whirlpool AWO/D 7141which I use once a week. I think I overloaded it by putting in a sleeping bag with my wash and the service light came on. I have since emptied the machine and disconnected from the mains and whilst empty been able to run the machine on a rinse programme, without a problem. I have just tried to do a wash but unfortunately it is coming up with F23 which is not listed in your faults; can you help me please
Regards John
Dear Sir,
Whirlpool AWO/D7452, Test mode sequence, Water fill right compartment, not the left one, no water in the drum, all the test mode cycle goes OK,
Is it only the water valve???
or could it be something else.
I think it is a 2 coil water valve, what is the part number?
Can I buy it from France and have a quick delivery?
Thanks for your help
regards
jean-paul bonn
Hi I have a whirlpool AWO D 8140 WP and it won’t drain I’ve taken what I thought to be the filter out which drained the water but it’s saying clean pump?
Good morning I would like to know the name of the tool that uses the display for the washing machine.
the videos are very good Thank you
Whirlpool AWOE 9760. Serial number 8592 005 15010
My machine is showing fault F12 which appears to be the heating element is short circuited.
Can you tell me where this element can be found and how I check it please.
Are you able to supply a new one?
Hello my whirepool awo/d 8600 wont start it normaly spinning and feel the amount of close. And now it doesen do enyting.
It got power the lights are on. No code in the display.
How do i enter the test mode? I have seen the film butt it dident work thank you for the answer
Whirlpool washing machine AWZ475
The end light and spin 0 rpm light remained ON after a wash cycle.
Power On/Off 1min, 1hr, 1day couldn’t help.
Please Help.
AWO43638 Start set a program, the light wash and rinse and rinse hold are light. But finally when start set a program no light only light. The washing machine not function. I don’t know this problem to solve it. Please help me.
My whirlpool awo /r4205 1200rpm washing machine service light is on.I have put it onto drain & pressed the reset button 4 times but the drum will not turn,I tried putting onto spin but nothing.
Jeg får feilkoder F23 på min Whirlpool awo/d 7116.
Noen som kan hjelpe.
how do you read the codes , are they a sequence of lights or do i need a meter
I have reset my whirlpool AW0/D050 and the rinse light is on as well as service light can you advise what the problem will be
Thanks Patricia