Printed Circuit Board Repairs for Tumble dryers AEG, Electrolux, Zanussi Etc
The video is on a common repair that i have to do on the ENV06 PCB and will show you just one of the faults that can occur
Even if you’re not a technician or an engineer, some Tumble dryer printed circuit board problems are obvious. Some common and simple problems can cause a printed circuit board not to work.
A thorough visual inspection of your tumble dryer PCB could save you having to buy a new board they can cost over £150 plus a needless engineers bill. Don’t be afraid to have a look. Just make sure your power is turned off to make sure you don’t get an electric shock.
Make sure it’s unplugged from the electric supply, now check all the connections are good tight and the pins are clean as you can get corrosion build up due to moister. You can Remove the cover from your tumble dryer PCB.
If the previous has not cured your problem you now need to remove the printed circuit board from the tumble dryer facial panel. Dryer covers are held on with screws and clips; this can vary from on different manufactures and models of tumble dryer.
The first inspection should be to check all the tracks on the circuit board look for water damage and also burnt tracks, due to the nature of the appliance there can be quite a lot of humidity on the board especially if the dryer has been kept in a very cold room or garage. Condenser dryers are more prone to this than normal vented dryers.
You are having to go into the realms of Electronics and if you do not know what you are doing you can cause more harm than good. You need to check for signs of damage to Components like Capacitors, Resistors, Diodes, Triac’s and the link Switch which fails so often on this type of tumble dryer. (Please note that when the LNK 304GN u. TNY264G blows the 47R Resistor also has blown) and you need to check all the Resistors & Diodes. I have put together a load of pictures on these Env 06 boards so you can get an idea of what to look for.
These pictures will help you understand some of the common chips that blow and there not always obvious
If you are not sure take the circuit board to someone that does what they are doing!!
Circuit Board numbers Env 06- 125988033 theses are fitted to all these makes Electrolux, AEG, Arthur Martin, Elektro Helios, Eureka, Faure, Frigidaire, Gibson Appliance, Husqvarna, Kelvinator, Marijnen, Parkinson Cowan, Progress, Simpson, Tornado, Tricity Bendix, Volta, Westinghouse, Zanker, Zanussi, Zoppas,
63 Responses to “Printed Circuit Board Repairs for Tumble dryers AEG, Electrolux, Zanussi Etc”

Hello!
I have a Zanussi ZTE 285 dryer and it was dead. I exange R76 (47ohm) Lnk304 and a resitor that was on position L3, by the colors seems to me to be of 10 ohm. I plug only the main board to power and the display is bliking and I also ear the buzzer intermitent.
Any ideas to solve this problem?
Thanks!
Hi Paul
I’ve just finished repairing our tumble dryer and it works!! Thanks for the video. I have just bought you a couple of beers.
Cheers,
Dave
thank you very much
Hi, i need your help, i have the same printed circuit but i have a transistor broken e i need the number to can change it. If is posible i can send you a picture to show you wat transistor i mean
My dryer AEG was dead. I replace INK304 and 47om resistor and it work 10 sec and stoped error E32. What to do?
Good evening,
Having some problems with a AEG T55840 Prod No: 916 096 276-15.
We actually haven’t used the dryer that much, but now there is no power to the machine at all. Could you tell me how to read the error (if there is one), and does this dryer also hold the Env 06 circuit board?
Hope to hear from you soon.
Thanks!
Thanks for info. Quite difficult to fine something like this in the net
Electrolux.
Replaced LNK304 and resistor R76 ( 47 or 43 Ohm forgot; it’s written there. But not 47 kOhm). And…. working)))))
Before was no lights at all with power connected.