Tumble Dryer fault code errors Aeg, Electrolux, Zanussi Etc
How to use the diagnostic mode for fault code errors
These error codes are for ENVo6 Cuirct boards tumble dryer  Electrolux, AEG, Arthur Martin, Elektro Helios, Eureka, Faure, Frigidaire, Gibson Appliance, Husqvarna, Kelvinator, Marijnen, Parkinson Cowan, Progress, Simpson, Tornado, Tricity Bendix, Volta, Westinghouse, Zanker, Zanussi, Zoppas,
If these fault codes apply to your Tumble dryer it should have a fascia panel on it like one of those shown below, there are four known variants covering quite literally hundreds of different models sold in the UK and across the EU.
Error Codes for Env06 Tumble dryer boards:
Â
E00
No alarm.
E21Â
Canister fill pump triac faulty.
Possible fault Wiring faulty; Electronic board faulty. Cycle interrupted. OFF
E22
Triac "sensing" circuit for the canister fill pump faulty
Possible fault Electronic board faulty. Cycle interrupted. Machine Status/Action OFF
E31
Conductimetric sensor signal frequency too high.
Possible fault Electronic board faulty.Machine Status/Action Alarm activated only during diagnostics.
E32
Conductimetric sensor signal frequency too low.
Possible fault  Wiring faulty; Brushes worn/faulty; Electronic
board faulty. Machine Status/Action  Cycle interrupted.
E33
It is displayed in the last alarm, if position 8 is NOTÂ OK.
Possible fault Wiring faulty; Brushes worn/faulty; Electronic
board faulty.  Machine Status/Action Alarm activated only during diagnostics.
E45
Door closure sensor.
Possible fault Door interlock faulty; Wiring faulty; Electronic board faulty. Machine Status/Action Cycle interrupted.
E51
Motor power triac short-circuited.
Possible fault Motor faulty; Wiring faulty; Electronic board faulty. Machine Status/Action Cycle interrupted.
E52
Intervention of motor overheating safety cut-out.
Possible fault Motor faulty; Intervention of motor overheating cutout; Wiring faulty; Electronic board faulty.
Machine Status/Action Power to the heater unit and reversal of the direction of rotation are interrupted. If the problem does not re-occur, the alarm is memorized and the cycle continues. If the fault persists after several attempts to supply power (about 35 min.), alarm E51 is generated.
E53
Motor triac "sensing" circuit faulty.
Possible fault Electronic board faulty. Machine Status/Action Cycle interrupted.
E54
Motor in-operational.
Possible fault Excessive wash load; Voltage too low; Motor/transmission system inoperative.
Machine Status/Action Cycle paused after several attempts at powering the motor. Start
E61
Insufficient heating (maximum time exceeded).
Possible fault  Heater unit faulty; Wiring faulty; NTC sensor incorrectly calibrated/out of position; Electronic board faulty.
Machine Status/Action Cycle paused.
E62
Power relay to heater unit faulty.
Possible fault Heater unit faulty; Wiring faulty; Electronic board faulty.
Machine Status/Action Forced cooling cycle.
E63
Intervention of auto-reset thermostat on the heater unit.
Possible fault Thermostat faulty (replace heater unit); Heater unit faulty; Wiring faulty; Electronic board faulty.
Machine Status/Action Disconnects the power supply to the heater unit. If the problem does not re-occur, the alarm is memorized and the cycle continues. If, after several attempts to restore power, the fault persists, alarm E62 is generated.
E64
Heater thermostat.
Possible fault Heater thermostat faulty: Wiring faulty; Electronic board faulty.
E65
Fan motor triac faulty.
Possible fault Fan motor wiring not connected; Motor faulty; Triac interrupted.
E66
Fan motor thermal protection.
Possible fault Fan motor wiring not connected; Motor faulty; Triac interrupted.
E67
Triac control faulty.
Possible fault Fan motor wiring not connected; CRM board faulty.
E71
NTC1 sensor faulty.
Possible fault NTC1 sensor faulty; Wiring faulty; Electronic board faulty. Machine Status/Action Forced cooling cycle.
E72
NTC2 sensor faulty.
Possible fault NTC2 sensor faulty; Wiring faulty; Electronic board faulty.
E82
Selector in OFF position faulty.
Possible fault Board wiring; board faulty.
E83
Selector positions wrong.
Possible fault Board wiring; board faulty.
E93
Error in the configuration of the appliance.
Possible fault EEPROM configuration incorrect. Electronic board faulty. Cycle interrupted. OFF
E94
Error in the configuration of the drying cycle. EEPROM configuration incorrect.
Possible fault Electronic board faulty. Machine Status/Action Cycle interrupted.
E97
Incongruence between selector and cycles.
Possible fault Configuration error. Machine Status/Action Cycle interrupted.
EA1
CRM board communication faulty.
Possible fault Board wiring; CRM board faulty.
EA2
CRM board protocol inconsistent.
Possible fault Software wrong; CRM board faulty.
EA3
Board selector faulty.
Possible fault Electronic board faulty.
EA4
Selector protocol wrong. Electronic board faulty.
EB1
Power frequency to appliance out of limits.
Possible fault Problems with the power supply (incorrect/interference). Electronic board faulty.
Machine Status/Action  Cycle interrupted. If a stable power supply is restored before the time-out has elapsed, the cycle resumes.
EB2
Power voltage too high.
Possible fault Problems with the power supply (incorrect/interference). Electronic board faulty.
Machine Status/Action Cycle interrupted
EB3
Power voltage too low.
Possible fault Problems with the power supply (incorrect/interference). Electronic board faulty.
Machine Status/Action Cycle interrupted. If a stable power supply is restored before the time-out has elapsed, the cycle resumes.
EC1
Voltage incongruence between boards.
Possible fault Problems with the power supply (incorrect/interference). CRM board faulty.
EC2
Frequency incongruence between boards.
Possible fault Problems with the power supply (incorrect/interference). CRM board faulty.
EC3
CRM resistance out of time (only in diagnostic mode).
Possible fault CRM group not connected; CRM group faulty.
EC4
Steam generator (CRM) heater relay.
Possible fault CRM group not connected; relay on board faulty.
EC5
CRM thermostat faulty.
Possible fault CRM group not connected; CRM group faulty.
EC6
CRM piloting faulty.
Possible fault CRM board faulty.
EC7
CRM pump triac.
Possible fault Pump wiring not connected; pump faulty; Triac faulty.
EC8
CRM pump diode.
Possible fault Diode on wiring short-circuited.
EC9
CRM pump piloting faulty. CRM board faulty.
ECA
Water tank empty.
Possible fault Tank level sensor wiring; tank level sensor faulty; water tube obstructed.
Hello,
I have Tumble Dryer Electrolux Mod. EDC78550W.
Don’t work. Error code E70.
What this mean?
Thank you,
Manuela
Zanussi Zachary 68560w no drum action it’s not belt non cap motor
hellow there,
i have a dryer aeg mod t75175av type p541657.
and it shows error code 62.
how can i fix this?
Best gerards
Stijn
AGE dryer keeps coming up with WHO error any idea why.
Thanks
Val
I have an Fan motor TRIAC faulty error E65 code.
how do i repair this on an AEG T59840 machine?
kind regards
Branko
Hello.
Anyone can help to identify this error code?
https://www.youtube.com/watch?v=osYehxP6zsE&t=29s
Thanks.
Hi,
I have a Zanussi zdc37200w pnc: 916 094 219(7) which appears to have the TC6 panel but in white. I am getting no fault codes but whilst there is power into the machine and down to the door switch nothing else gives me the impression the machine is powered, can’t find a service manual or wiring diagram online for it but am assuming there is an interlock somewhere which has failed – any idea’s ?
Regards – Alex.
Hi,
I have aeg 59840 and it gives error e32 any ideas. It works but the drying pump does not start.
Regards
Hi,
I have EDC67150W,when switch on power supply,the LED lights doesnât appear.plug fuse is working fine may I know what is the possible cause?
If you have a question about a fault on an appliance please use the contact form instead. Questions on faults in the comments will not be answered.
Hi,
my dryer is Tc3 facial panel
and working only 1 Minute
help me
Thanks
If you have a question about a fault on an appliance please use the contact form instead
Hi, my dryer is Tc3 facial panel and working only 1 Minute help me Thanks
If you have a question about a fault on an appliance please use the contact form instead.
AEG Tc09h6shw….error code EH0. Any ideas
Regards.
Hello!!
I’m in troubles…ha, ha, ha. I need your help, I have a Heat pump tumble dryer with a low efficience dry, no water is collected, the compresor is running well, but the air isn’t hot, and the radiator has been straight cleaned.
It’s a T59850 AEG/Electrolux dryer.
Since aprox. five years ago it’s showing a e32 error code, when I change a motor capacitor and replace a motherboard fuse and triac thanks ti your YouTube videos. Now I’m lose…
Thanks a lot for your help that I’d yet received un your videos. Bye.
Hello, I have a fault on an AEG LAVATHERM T56830 tumble dryer. It runs for about 10 seconds and then ends with the END light illuminated (there is no display panel for a fault cordon this machine). What is the possible cause please.