Flashing Lights & Error/Fault code
An error code will be displayed on your washing machine or washer/dryer if the machine has a problem. Error codes will be displayed on your machine in one of two ways: Either on your digital display screen which will show an error code in a letter followed by two numbers format, Or washing machines without digital display it will show a series of flashing lights.
There are different ways that these are displayed so you will need to consult your manual on these or let us know your full model number with the fault sequence and we will try and help you.
These lights when flashing should be read in a binary fashion, these are the typical Hotpoint, Ariston, Indesit & Creda error codes or fault codes for washing machines and dryers.
Now there may be some variances for older models, but there are 3 main types of board listed so you need to know what you are looking for. This video is on How to Repair Washing Machine Flashing Lights.
Hi, My Hotpoint WF340 won’t spin or drain door locked final spin on/off are flashing, sometimess the lights go steady as if it’s going to start then they flash again, any advice would be great, thank you.
I’ve got a Logik L612WM15, I’ve loaded the machine and set required programme but the wash and rinse lights are flashing and machine isn’t responding – any ideas ? Machine is only 10months old
hello there and thanks for helping me on an earlier occation, now my ariston aml 125 is acting up on me again.
this time the lights for door lock is blinking rapidly and the postpone start and fast wash button is blinking.
Blingking rapidly and the postpone start and fast wash buttonis blingking please help
Hi Paul
I have an indesit WIDL126 machine
This morning when I turned it on all nearly of the lights were flashing. From left to right these were
Delay Timer, Easy Iron, Extra Rinse, 1200-600, lock light as well as the 9h light. I turned the machine off at the plug and now when I turn it back on there are less lights flashing …just the Delay Timer, 1200-600 and lock light are flashing.
Please could you tell me what might be wrong with it
Thank you
Hello,
I’ve just found your very helpful website but it hasn’t covered my problem with my Hoover SE 147 washing machine.
It has stopped mid-cycle and the led between the spin and cold wash buttons is repeatedly flashing 4 times. The powder tray is empty but the conditioner is still in its tray.
You guidance would be very much appreciated please.
Many thanks,
Christopher
HI we have Indeset WiXL123S /1200 the delay & stain removal LEDs are flashing along with the lock led
Please can you advise as to the problem and it’s cure
Thanking you in anticipation
Best regards Steve & Chris
sorry for the late reply
You need to have a look at this article and workout the other code
Indesit error codes
Appliances Engineer
Hi,
I have a aquarius hot piont washing machine which is 11 years old, so far have never needed any work done as never broke down but other week all the lights keep flashing when i put it on, it did do my washing but i called my insurance and nobody came out to see it they just said it will cost to much to get a new one, but they will only give me £56 towards the cost. I’m thinking of getting someone out to look at it do you think the cost of repair will be large.
sorry for the late reply
Without seeing the way the lights are flashing It’s very hard for me to understand the fault, you could upload a video to YouTube and send me the link for me to see it,
Appliances Engineer
Thanks you guys I was about to scrap my hotpoint and buy a new one ? (On job seekers too) but I replaced capacitor as per your video and everything is running fine now! So grateful thanks again .John
No problem I’m glad we could help please remember to subscribe to a channel.
Appliances Engineer
Hi Simpson washer flashing right to left happened
When host burst wetting walls and maybe machine
How can I fix as it won’t start
My washing machine shows yellow blinking light on intensive and prewash then it stops wat do I do
I have a Hotpoint Aquarius WF220. The time saver light is flashing, rinse and spin light on constantly and On/Off light flashing quickly. I have to switch off at mains to cancel lights.
Any ideas what fault may be?
Thanks
Hi Paul,
I have the very same washing machine as in your video and have found that not only C17 but also C20 have domed at the top?
It is a 470uf 10v. Do you sell this as well?
All the best
Kieran
Hi there,
Aquarius Hotpointo washer dryer has flashing lights continously on all buttons, any advice? I’ve tried turning it off and on and leaving plug out but nothing us working.
My hot point washer keeps flashing f15 at the end of a cycle antone know what’s wrong with it thanks
My hotpoint condenser tumble dryer is flashing lights showing f06 code and red lights flashing on empty water clean filter etc They didn’t need cleaned emptied but did anyway Can you help on what I should do next Machine only 5 months old Thanks
I have a Hotpoint Aquarius WF321 and all lights are flashing constantly at the same time. I have tried turning the power off and back on but still the same. Do you know what has caused this and how I can rectify this. Thanks.
U need a new washer
when you have a question please use contact us page for 24 hour response https://www.how-to-repair.com/help/contact-us/
Get Appliance help from Paul, Email him
Appliances Engineer
Hi Simpson. Fingers crossed you can help.
I’ve got a Hotpoint Ariston CAWD 129. Put a load on yesterday and it started off well. I could see the drum spinning. When I came back at the end of the wash all the function lights and the start/pause were flashing. When I got the towels out at the end they were super wet as if the final spin hadn’t happened.
I’ve had the machine off and on several times, including overnight, put it on a short wash, put the spin on only, etc. The drum still won’t spin. The pump is working, but the drum isn’t. Every different cycle ends the same with the lights flashing.
I’ve pulled the back off and the belt is good, I’m not sure which connections to test with the multimeter.
Wondering if you have any other ideas.
THANKS!
Hi
I’ve taken the board out and have checked out the capacitor. It doesn’t look like a dome like in your video, but I guess changing it won’t hurt. I have the following written on the capacitor v10uF450. should I use the one on this site or find the exact match?
Thanks
I have an f3 error code flashing on my Hotpoint washing machine. I have replaced the temperature sensor but the problem still there. Any advice on next step please?
I have a hotpoint aquarious and all my lights are flashing and it just stops.
sorry for the late reply
Without seeing the way the lights are flashing it’s very hard for us to understand the fault, you could upload a video to YouTube and send us the link if you still trying to fix it.
Iv a hotpoint washer dryer n all lights are cuming up flashing wot does this mean please can u help me
when you have a question please use contact us page for 24 hour response https://www.how-to-repair.com/help/contact-us/
Get Appliance help from Paul, Email him
Appliances Engineer