Refine your search
You can refine your search further by entering make and model number if you are looking for parts. If you are looking for tutorials please use appliance type only. If you need help please use FAQs or ask a question in contact us page (make sure you have full model number)
Having trouble with layered Navigation? Watch Video
Our How-to-repair stores
How to service a Hoover Candy condenser tumble dryers
Hoover Candy Condenser tumble dryer are relatively easy for most people to fix if they are reasonably competent in DIY and working with electrical products as they really are rather simple appliancesThis video can be used on Hover and Candy models of Condenser tumble dryer
Hoover Candy tumble dryer empty water Indicator flashing, runs for a few seconds then stops
Tumble Dryer Float Switch This video shows you Hoover and Candy tumble dryers flashing the full water indicator light. This is most commonly caused exactly because the water container is full of water, so make sure to empty it every time you dry clothes on it. The other error that may cause this is possible the pressure
E21, E22 Error Code, Tumble Dryer Pump Fault AEG, Electrolux, Zanussi Etc
This video will help you understand the fault and show you how to replace your pump or float switch.These error codes are normally related to a Tumble Dryer Pump Fault E21, E22 Error Codes are listed below.
Condenser Tumble Dryer how to replace the pump unit.
If your Condenser Tumble Dryer keeps showing the empty light and the tumble dryer will not start then this video will teach you how to replace the pump unit.This video will show you how to replace a Condenser Tumble Dryer pump and float switch system when the water light stays on.How to fix &
Grundig GTN38240GCW Heat Pump Tumble Dryer Condenser Lift Pump Is Continuously On When Turned On At Mains
Grundig GTN38240GCW Heat Pump Tumble Dryer’s pump failed so replaced with genuine new pump and float switch.
Now the pump is on continuous when machine has mains supply regardless of if machine is on or off. Looked at float switch, activating correctly when compressed stopping cycle but not pump. Took machine apart and followed your service video.
No obvious issues. Don’t think it’s the pump or float switch. Maybe whatever sends signal to pump?? Any help greatly appreciated thanks for your time. James
Beko DTBC10001W Tumble Dryer Empty Water Light Keeps Flashing
I have Beko DTBC10001W Tumble Dryer. I’ve changed pump and float valve switch but the water in the bottom collection area isnt draining, we’ve double cleaned the condensing unit and vents but still having the problem, is there anything else that could be causing the pump to not kick in?
Hoover Condenser Tumble Dryer dxc9tceb-80 E21 –
Hi, pump runs when 230v placed across the terminals, float level switch opens/closes, continuity of cabling from pump and switch to PCB connecter confirmed OK
I suspect main board but cant remove knob to examine board, thoughts?
Chris
Hotpoint Condenser Tumble Dryer FETC70BPUK first edition Noisey Pump
Good morning, I have had this tumble dryer for a few years now and recently I have noticed that when the Float rises up and pressed the float switch. The Empty water light comes on. My question is…. should the machine cut out when the empty water light comes on? and if so what parts should I look into to replace this fault?
Hotpoint Condenser Tumble Dryer TDWSF83BEPUK F12 and F19 errors
TDWSF83BEP on 15min timed programme runs til 5 mins remaining, both high & low heater sides run at approx 10amps for 5 mins then drops to approx 5amps just low side(heats, spins both ways, pumps etc.up til this point) carries on for several more minutes then F19 error. Heat element 2 x 1200w, 42.5ohm each total=85ohm. Heat stat (type261/bp 180deg 20-16)180deg cut out reads short cct, heater ntc (type 279 23-16 3111 T200)approx 12kohm @ 20deg, decreases with heat. Fan ntc(2790046 48-16)12kohm @ 20deg approx decreases with heat. Fan, ducts, filters, condenser, water reservoir all cleaned and clear. Flood float reed switch normally short cct (empty reservoir), open cct when lifted. Condenser reed switch normally open cct, short cct when condenser unit in situ. Control bd diodes, resistors, caps all within reasonable tolerance, relays operate in-cct with 9v applied, short or open cct.
Display bd checks ok, mom switches, diodes. leds, resistors ok. Max6959 (display interface) not tested but appears to function ok, 7 segment display working ok.
Wiring checked for continuity, shorts, leaks etc all ok.
Direct drive motor not yet checked, cct bd on motor, Askoll type TA0200, would need to remove bearings to gain access to cct bd.
Is the motor/cct bd the likely culprit here?
Apologise for lengthy detail but driving me nuts, thanks.