Beko Condenser Tumble Dryer DC7112W KEEPS TRIPPING ELECTRIC
Every time i switch start button on it trips out the electric rcd .
anthony haywood
I will try and help with Beko Condenser Tumble Dryer DC7112W problem.
This is normally one of two problems which are quite common as this is a condenser tumble dryer sometimes when the filters and ducting gets restricted in airflow in other words the machine has not been maintained very well a large amount of moisture can gather around the heating element this would cause the RCD in your electrical board to trip, the second most common problem is you have a faulty motor this is straightforward it will just need replacing but you will need to check these items with an insulation tester or a mega. the most common to fail is the heater as these machines do get a lot of moisture around the element.
I have added some videos below to assist you in any repairs and also a full exploded diagram of your machine showing you all the components and a full list of parts below that
If you want to support the site please mark us to your favourites, also I would be grateful if you would subscribe to our social media channels as this really helps my site and keeps us going.
YouTube. http://www.youtube.com/user/howtorepair
Facebook. https://www.facebook.com/how.to.repair.appliances
And if we really helped you save money you can always click on the Buy Paul a Beer page
Common Beko Condenser Tumble Dryer DC7112W faults with links to the right repair guide
I have included a lot of videos in the links below on these tumble dryers to assist you in repairing your tumble dryer; I have also included an exploded diagram of your machine with all the parts that you need listed below that just click on the relevant and it will take you to a search result
- No heat
This is the most common fault on tumble dryers.
Vented dryers: this can be a fault with the thermostats, heater, or on some occasions, it might be the timer or the relay on the printed circuit board.
Condensor dryers: this might be any of the above but you also have a condenser plate that collects the water and then is either pumped to the collection tray or flows into a tank. Check pump unit and float switches.
Heat pump dryers: these are much more complicated they use a refrigeration prosses to heat the cloths and use the cooling side to condense the water for collection. Check compressor is running, check NTC sensors and check filters, and also that it has the right amount of refrigeration gas (normally only done by an engineer)
- Drum not turning
This will stop the dryer from drying. You may have to replace a faulty belt or in other cases, look at the motor, motor capacitor, or the jockey wheels. Again there are relays on printed circuit board types that can go faulty.
- Not starting
Whilst, not a common problem, you may have a faulty door switch, starter relay if fitted, or can be start button or PCB.
- Noisy Machine
This is usually caused by faulty bearings, jockey wheels or worn felt pads. The motor can get dust build up in the bearings, also the fan blades can distort in shape and make noise rubbing the housing.
- Water leaks.
This can be a simple as the water tank (in a condenser tumble dryer) has not been emptied, or not placed back into the housing correctly. The condenser plate can need cleaning. The pump unit might not be working. Or the ducting system can be clogged with fluff etc. See servicing tumble dryer.
- Tumble dryer reports a fault code or error code.
Error codes can be on the display or given in certain lights flashing sequences. Tumble dryer fault codes are not universal but may only point you or an engineer in the right direction they are not 100% accurate they are only that for guidance. Your owner’s manual may help you identify the problem and even suggest a fix. In other cases, you’ll need an engineer to trace the fault. Don’t be tempted to ignore a fault code, even if the dryer seems to be functioning normally. Some codes are ‘early warning signs’ and fixing the machine at an early stage could save you time and money in the long run.Contact us with the full model number and detailed description
Reference | Part Number | Description |
---|---|---|
1 | 2963930100 | TOP PLATE |
10 | 2976900100 | FRONT DOOR ASSEMBLY |
1003 | 2971650300 | CAPACITOR (ARCOTRONICS 9 uF) |
1044 | 133000001 | WASHER 12x18x1 DIN 988.. |
1045 | 160200200 | ZEEGER 9x1 DIN 6799 DRCS68 |
1046 | 2973900600 | REAR PANEL ASSY |
1087 | 2963110100 | HOSE AND CABLE HOLDER |
1098 | 2962630100 | FAN COVER - COOLING |
1199 | 2957880100 | SWITCH HOLDER |
12 | 2962120100 | INNER DOOR_(ARES_ARC1_WITHOUT_SWITCH) |
1205 | 2707730100 | PLASTIC SCREW (DIAMETER 3x6) |
1209 | 2969500300 | LOCK BODY ASS |
1211 | 2963910100 | LIGHT GUIDE |
1230 | 2961000100 | WATER CONDUCTOR ASSY. |
1231 | 2985800100 | WATER HOLDER ASSY. (GASKET) |
1240 | 2953510100 | O-RING (17,86X2,62) |
1241 | 2953520100 | O-RING (9 X 2) |
1244 | 2979290100 | POMP COVER |
1256 | 2973100200 | SHAFT-FRONT BEARING ASSY |
1259 | 2972300100 | FILTRE CASETTE ASSY |
1260 | 2972870100 | OVERFLOW FLOAT |
1268 | 2963670200 | LIGHT GUIDE SET |
1271 | 2970020100 | AIR GUIDING PART |
1279 | 2962560300 | BEARING SENSOR COVER |
1287 | 2960150100 | RUBBER STOPPER |
1290 | 2962590100 | DOOR GASKET |
1295 | 2963120100 | MOTOR BRACKET CLAMP (PLASTIC) |
1313 | 2705810300 | PT SCREW (3_5x8) |
1314 | 2983560100 | COOLING_AIR_EXIT_ROUTER |
1377 | 2965200600 | MAIN CABLE ASSEMBLY |
1390 | 9002900200 | COUNTERSUNK HEAD SCREW (PT-4X14) |
1391 | 2951610300 | DELTA PT SCREW(5x20 TORX HEAD_PERFOR.) |
1398 | 2951780300 | DELTA PT VIDA 50x26 WN 5454 HB |
1399 | 2960680100 | NTC-THERMOSTAT GASKET |
14 | 2962170200 | HINGE |
1401 | 2963210100 | MOTOR SHAFT SEAL |
1417 | 2705810400 | PT SCREW (3_5x14) |
1440 | 2961690100 | ADJUSTABLE PLASTIC FOOT |
1451 | 2963180200 | BACK COVER FELT |
1453 | 2953741500 | SINGLE ADHESINE EPDM FOAM |
1454 | 2963090200 | AIR GUIDING GASKET |
1455 | 2962810100 | SIDE WALL PIN |
1459 | 2974680200 | WHEEL (RUBBER) |
1459 | 2987300200 | WHEEL (RUBBER) |
1460 | 2951261200 | POMP WATER TANK HOSE. |
1462 | 2951260800 | POMP WATER TANK HOSE. |
1466 | 9003272000 | PLASTIC SCREW (DIAMETER 4x10) INOX |
1469 | 100700120 | SCREW (B4.2*9.5 DIN 7982-H) |
1471 | 2953741100 | SINGLE ADHESINE EPDM FOAM. |
1473 | 2962390100 | LOCK MOUTH |
1478 | 2963420100 | WATER COLLECTOR |
1481 | 2963950200 | COLD AIR ROUTER |
1483 | 2963250100 | COOLING AIR OUTFLOW FELT |
1484 | 2963590100 | YAN DESTEK (SAG-54CM) |
1485 | 2963610100 | SIDE SUPPORT (LEFT) |
1486 | 2974470700 | SHAFT DRUM COVER SHC ALS |
1486 | 2974470300 | SHAFT DRUM COVER |
1486 | 2974470100 | SHAFT DRUM COVER |
1489 | 2962290100 | DOWN HINGE GUIDE |
1490 | 2962310100 | UP HINGE GUIDE |
1497 | 9003271700 | PLASTIC SCREW |
1504 | 2982700100 | FLUFF FILTER ASSY. |
1517 | 2953741400 | SINGLE ADHESINE EPDM FOAM |
1587 | 2966990100 | CABLE TRAY |
1588 | 2967080100 | RACEWAY SOCKET GUARD |
166 | 2978270100 | MAIN CABLE ASSEMBLY |
169 | 2970445400 | POWER SUPPLY CORD |
18 | 2973500100 | ADJUSTABLE PLASTIC FOOT ASSY. |
180 | 2964170100 | ON_OFF SWITCH(ROLD (+) FORM) |
186 | 2963163001 | ELECTRONIC PCB ASSY.(TERRA AV BAZ_PRIME) |
189 | 491500303 | POLY-V 285 H 4 MA BELT |
200 | 2975209027 | PANEL BODY |
2013 | 2970540100 | POWER PLUG HOLDER |
203 | 2976702100 | PROGRAMME KNOB BUTTOM_ASSY |
2071 | 2972960100 | DUAL SOCKET COVER |
2072 | 2972950100 | DUAL SOCKET CASING COVER |
208 | 2963669027 | PANEL BODY |
300 | 2963680100 | FUUNCTION BUTTON |
33 | 9001230800 | PLASTIC CLAMP 152 mm |
339 | 2963640100 | OUTER DOOR |
341 | 2962150100 | LOCK HOOK |
401 | 2963580100 | FRONT PANEL |
402 | 2965080100 | FIXER |
412 | 100601820 | SCREW (B4.2x16 DIN 7981-H) |
4210 | 2974870100 | INTERFERENCE FILTER |
43 | 2960311135 | USER'S MANUAL (EU LANGUAGES) |
468 | 2963710100 | ON OFF BUTTON (TIP02+ARC 734 MAVI) |
48 | 2985421700 | DRUM ASSEMBLY |
481 | 2959000100 | SELECTION SWITCH ASSY. |
581 | 2966980100 | HEATER CABLE GUARD |
583 | 2705870100 | SELF LOCKING CABLE HOLDER |
584 | 2967011100 | DRUM LIFTER |
59 | 2962470200 End Of Life | ELASTIC POLY-V BELT. 7PH 1956 |
63 | 2971420100 | Dryer Motor Group WELLING |
632 | 2962160100 | HINGE BUSHING |
65 | 2970102000 | HEATER ASSY |
750 | 2961850100 | PCB HOLDER |
804 | 2973801100 | REAR DRUM TIGHTNESS PLATE ASSY |
804 | 2973800700 | REAR DRUM TIGHTNESS PLATE ASSY |
804 | 2973800100 | REAR DRUM TIGHTNESS PLATE ASSY |
822 | 2963540100 | KICK PLATE - LEFT |
826 | 2972900800 | HEATER COVER ASSY |
826 | 2972900500 | HEATER COVER ASSY |
827 | 2962020100 | UPPER BEAM |
8303 | 9003270200 | PLASTIC SCREW |
8318 | 2002370900 | HOSE CLAMP (Ø 16.4) |
8320 | 100601520 | SHEET METAL SCREW (B4.2X13 DIN 7981-H) |
834 | 2959400200 | REAR BEARING ASSEMBLY |
8384 | 9003270100 | PLASTIC SCREW |
8385 | 9003270400 | PLASTIC SCREW (4_10) |
8386 | 9003270500 | PLASTIC SCREW (4_12) |
8388 | 2966700200 | SUPPORT PART OF SHEET TOP PLATE ASSY. |
8392 | 9003610300 | sheet metal screw(B4_2x9_5-perforated) |
8394 | 2705810100 | PT SCREW (3_5x9.5) |
8397 | 9003610100 | SHEET METAL SCREW(B4_2x9_5-perforated) |
8403 | 9003860300 | SHEET METAL SCREW |
8413 | 120800120 | FIBERED_NUT_M6X1_DIN_985 |
8415 | 2826510200 | DOWEL PLASTIC CLAMP |
8419 | 2963340100 End Of Life | WASHERED NUT (M6x1) |
842 | 2960190100 | CABLE HOLDER |
8422 | 2951580400 | COUNTERSUNK HEAD PT SCREW (4.5x12) |
8428 | 2971870100 | MX10 RYSB PERFORATED SCREW |
843 | 2964470100 | WATER TANK (BOTTOM_7KG_54CM) |
8434 | 2951780400 | DELTA PT SCREW |
844 | 2958330200 | WATER CAP BOTTOM |
845 | 2963530100 | KICK PLATE - RIGHT |
846 | 2962680100 | CONDENSER SNAPPER |
847 | 2975700700 | PLASTIC CHASIS ASSY |
856 | 2974940100 | HINGE PIN HOLDER (PLASTIC) |
857 | 2963150100 | SPRING |
861 | 2963330400 | FRONT SELING FELT |
873 | 2963230100 | PCB HOLDER COVER |
877 | 2971100100 | PROCESS FAN ASSY |
888 | 2951060600 | MICRO SWITCH |
888 | 2951060700 End Of Life | MICRO_SWITCH |
888 | 2951061000 | MICRO_SWITCH |
891 | 2961680100 | COOLING FAN |
9 | 2963650100 | HANDLE |
906 | 2961190200 | SPECİAL WASHER (8,1*17*1,5) |
921 | 2980000300 | CONDENDER ASSY. (54CM) |
921 | 2980000200 | CONDENDER ASSY. (54CM) |
925 | 2953450400 | THERMOSTAT ASSEMBLY(L_950MM_78+-3 C) |
925 | 2953450700 | THERMOSTAT ASSEMBLY |
932 | 2961961100 | SIDE PANEL |
985 | 2954700100 End Of Life | Micro Switch Ass. |
985 | 2954700400 | Micro Switch Ass. |
Have a beko tumble dryer and just went to use it amd there’s no power to it at all. I’ve cleaned it out very well as usually in filters in all. Also it’s not the power fuse tried reseting it, but still to no use.
Cam you help please
Thanks Gavin Kavanagh