NEW REPAIR GUIDES

FORGOT YOUR DETAILS?

AAH, WAIT, I REMEMBER NOW!

Beko washing machine self test & diagnostic mode

by / Monday, 27 July 2015 / Published in Washing machines

How to enter test mode Beko washing machine to find the fault

 

When looking at the dial on a Beko washing machine treat it as a clock 1 to 12 as in picture.
On some models you may have more programs but for the basic access into the diagnostic mode is the same the same

How to enter test mode Beko washing machine to find the fault

Start by turning the washing machine of with door shut.

Now turn the dial to the position 1 Which is normally the 90c hold the start /pause button down while you press the on/off button to on for a couple of seconds till light flashes

Now turn the dial to the position 6 and hold down a few seconds the next time you enter it should turn on all the lights now you are in self test diagnostic mode:

Every time you Press the on/off button it will change the test function.

1st all the lights will show

 2nd will not do anything

3rd This will tell the motor to turn at standard wash speed clockwise with pump emptying.

4th This will tell the motor to turn at standard wash speed anticlockwise with pump emptying.

5th This will tell the motor to spin clockwise with pump emptying.

6th This will activate right hand compartment water valve. Please note machine will keep filling until you stop it.

7th This will activate left hand compartment water valve. Please note machine will keep filling until you stop it.

8th This will activate booth water valves together. Please note machine will keep filling until you stop it.

9th will not do anything

10th this will start fill cycle until water activates the pressure switch at normal fill level (Normally just below the glass on the door) when the Beko washing machine has reached the level it will start clockwise rotation at normal wash action and heat the water. Please note You Have to stop it manually.

11 this will activate the pump only to empty.

Press again and you are back at the start. Turn machine of and leave for a few minutes and the switch back on and you’re in normal wash mode.




70 Responses to “Beko washing machine self test & diagnostic mode”

« Older Comments
Newer Comments »
  1. Baristu says : Reply
    February 22, 2018 at 12:11 pm

    Forgot to put into floor drain the drain hose still hanging at the back of my beko washing machine when it drain. And it get wet and start to smell burn rubber. Do have a chance to fix and where should I look the possible damage part..

  2. Rose Marie Gauci says : Reply
    May 26, 2018 at 3:44 pm

    Why is the end signal sound being heard throughout the whole cycle. Beko WM Y 91443LB1: Thanka

  3. Audrey says : Reply
    May 28, 2018 at 5:17 pm

    Beko washing machine wmi71641 programmes not working Seems to be stuck on spin and drain mode

  4. michael says : Reply
    July 18, 2018 at 11:23 am

    my wahing machine will not perform a diagnostic test

  5. Laurence says : Reply
    August 24, 2018 at 2:51 pm

    wm74135 only the pump starts to run when trying to start a programme nothing else happens
    checked filter and its clear
    Is it a programmer fault ?
    can you help

  6. Steven says : Reply
    September 5, 2018 at 5:49 am

    Hello, I have a WMY7046LB2 washer. Is there a diagnostic mode for this model??

    Thanks

  7. Grateful Consumer says : Reply
    November 17, 2018 at 8:47 pm

    Thank you ever so much for this amazing advice,I was so distraught when my washer stopped working,it was like it was stuck with a humming noise,as always it couldn’t have happened at a worse time,but luckily I found your amazing advice and my beloved washer is back and working lovely 🙏
    You sir are a legend!!! 😉

  8. Liam Chambers says : Reply
    November 25, 2018 at 12:13 am

    Hi mate
    How do I get a Beko washer dryer combo wda8514h into test mode

  9. Gary Bolter says : Reply
    November 26, 2018 at 11:57 pm

    Fabric softener not emptying why?
    Please advise

  10. Cheryl Donovan says : Reply
    April 4, 2019 at 4:49 pm

    WMI71641 Machine stuck in spin mode but not spinning.Just running through the program but not spinning

  11. Gary Riding says : Reply
    April 21, 2019 at 12:45 pm

    We have water coming out from under the washing machine and it is not leaking from cold water intake hose or from drain hose

  12. Frank Gibson says : Reply
    June 4, 2019 at 2:19 pm

    Beko washing m/c model WMB61631W serial 5023790025911 (left by previous flat occupant).
    Select wash programme, IF the display lights up, press start button and it trips the MCB in the consumer unit.
    Other times it trips the MCB as soon as the wash programme is selected.
    Tried it through a plug-in RCD, it tripped the latter AND the MCB.

  13. david anker says : Reply
    July 11, 2019 at 1:51 pm

    on standard wash 28 min time reaches 16 min and stops taking in water .tap symbol appears. if manually fill machine when water reaches desired level programme continues to 12 min. same again. after 12 min programme continues to end as normal but machine continues to slowly take in water so cant release door

  14. IRENE HENDRY says : Reply
    October 12, 2019 at 8:44 am

    good site but my beko WMB71231B DOES NOT HAVE A on off position to go into diagnostic mode how do I do this?

  15. Diane Miles says : Reply
    November 4, 2019 at 8:41 pm

    Hello
    I have a Beko washing machine Model No. WMB101433LW
    Problem: It starts to fill in the third compartment then should switch to the soap powder compartment when it stops except that it doesn’t it again starts to fill water into the third compartment this continues for some time then seems to give up, it eventually drains and the End sign shows. Is there a solution please.

  16. Paul says : Reply
    December 6, 2019 at 12:11 am

    My washer was doing a wash then as it half way thew it chipped out and blew electric it spins still and I done a quick wash it done it but cut out out at last min I done a long one wer it dry it more chipped out half way thew wat would u think its is pls

  17. Paul askew says : Reply
    January 10, 2020 at 1:45 pm

    We have a bell wmx86231w the drum of the machine will not rotate for wash or spin can you suggest what the the cause of the problem may be
    Regards
    Paul

  18. Kuldip Patel says : Reply
    January 16, 2020 at 4:47 pm

    I have a Beko washing machine which has been working fine until I moved house recently.

    Now it does everything but the fast spin at the end of the cycle. So it spins normally, fills with water and drains the water but when it comes to the fast spin part it just stops leaving all the clothes sopping wet.

    I have put it in test mode and the fast spin does not work, so it can’t be a belt problem but not sure what it could be.

  19. Viliami says : Reply
    February 26, 2020 at 10:38 am

    I am after the buttons to press to enter the service or test mode. It’s for Beko WMY 9048LB1 washing machine. Any assistance will be much appreciated.

  20. John Rowley says : Reply
    April 13, 2020 at 11:17 am

    My Beko washing machine WM74165W is not rotating under program and making a terrible noise, but is rotating freely and I have checked that the drive belt is on. The drive belt wheel and motor wheel rotates freely when the drive belt is turned. Could the problem be something to do with the motor or what? Pump did not pump all the water out, so could it be the pump making the noise?

« Older Comments
Newer Comments »
24h technical help answers

Questions on faults in the comments will not be answered. Please use the contact us form instead.

TOP