FORGOT YOUR DETAILS?

AAH, WAIT, I REMEMBER NOW!

Beko washing machine wmb 7, 8, 9 Series diagnostic & test mode

by / Tuesday, 10 May 2016 / Published in Washing machines, Water Systems & Valves

How to enter test mode on Beko wmb 7, 8, 9 Series washing machines diagnostic & test mode to repair faults and test errors

Beko Diagnostic

 Important notice on Beko 

Before entering test mode please be aware that you are not meant to leave the washing machine Unattended. There is a chance the machine can overfill when testing the water valves or the Machine could overheat when testing the heater. Also when entering the test mode make sure the drum is empty as not to cause damage when on spin mode:

This video can be used on all these makes

WMB81431LW, WMB71231B, WMB61631W, WM5141W, WM5141S, WMB71422S, WMP601W, WMP541W, WMB81241LS, WML72S, WASH814DW, WMC6100W, WMB61021W, WMB71642S, WMB61431W, WMC6140W, WMB71021W, WMB61631S, WMB81241LB, WML72B, WMP652W, WMP631S, WM74135W, WMB61221S, WMB71231S, WM74155LW, WM74155LS, WMB61431S, WMB51221W, WM622W, WMB61431B, WMD61W, WMB51221S, WMP501S, WMB61221W, WM7355S, WMB81221LS, WMC6100S, WMB81241LW, WML72WXC, WMC6120W, WMB91242LB, WML15105D, WM5100W, WME8227W, WMB71442W, WM85135LW, WME7227W, WME7247W, WM5100S, WMC62W, WM6123W, WME7267W, WMC61W, WM6103W, WM6123S, WME7227S, WM6167W, WME8227S, WM5121W, WM6111W, WMP621W, WM612W, WM6355W, WME7247S, WMC61S, WM5121S, WM6167S, WME7267S, WM7335W, WME8227B, WMB91242LC, WMI71641, WMI7462, WMI71441, WMB71231W, WME7227B

Test Mode Sequence

If you have problems with the drum not turning or spinning. Then check the carbon brushes in the motor first and test the motor separately before running this Diagnostic sequence as you could do damage to the PCB.

 

To enter test mode.

 It is advisable that washing machine be switched off or at least 5 minutes prior to entering test mode

With the machine switched off shut the door and turn the dial to the 12 o'clock position. Now press and hold down the start/pause button and press the on/off on, while holding the start/pause button down for 3 seconds until the display shows a number or error code.

  Now that you've entered the Diagnostic / test mode, remember every time you press the start/pause button this will be one advance the program to a new test.

  • 1: All the the display or led’s will flash to check that they are working and door will now be locked.
  • 2: Drum does a clockwise rotation.
  • 3: Drum rotates anticlockwise rotation 
  • 4: Goes into spin mode on clockwise rotation make sure there are no clothes in machine before performing this test as washer will spin at its fastest rpm. 
  • 5: right hand water valve check
  • 6: left hand water valve check
  • 7: both water valve are now activated and all 3 compartments will have water flowing in. 
  • 6: This is the full wash and heat test. Machine will start to fill to the correct water level and continue to heat and wash.
  • 7: the machine will empty. the pump should drain the water away.
  • 8:After it has finished turn the machine off and on this will go back to normal mode.

 

entering test mode one beko washing machines

Tap symbol showing as fault

Beko washing machine error Diagnostic fault codes

Turn dial to 12 o'clock position

Beko washing machine E08 Error code

Error code showing fault

beko washing machine fault codes and error codes

Display will flash when in test mode




Tagged under: , ,

134 Responses to “Beko washing machine wmb 7, 8, 9 Series diagnostic & test mode”

« Older Comments
Newer Comments »
  1. George Tanu says : Reply
    December 13, 2016 at 9:31 pm

    I have a BEKO wmb71642s. Yesterday after a 1200rpm spin i started to notice a bit of burning smell then a bang then the fuses on the house tripped. From then on the machine wont turn and spin, everything else works. Display and programs, even water in and draining work. I have checked the carbon brushes and they are only half way worn, cleaned them a bit but didnt clean the copper point of contact with the brushes, it is black there but not deposits. Could there be an issue with a motherboard fuse or capacitor?..then how can the display work fine but only spinning not? I would appreciate some help. Thank you

  2. Frank says : Reply
    December 25, 2016 at 10:33 am

    Dear Sir, We have a problem on our washing machine model WMB 81242 PTLM. The fault is when select any program, the machine starts spinning on all modes, Please, if possible can you send me your advice.

    Thanks and regards

    Frank

  3. Matt says : Reply
    January 18, 2017 at 6:57 am

    Hi Paul

    I found this great website from a link on one of your videos. We have a Beko WMY 8068 LB1. It is showing error code E12. I was thinking to maybe try and put it in diagnostics mode to clear the code, but the dial doesn’t have an indicator mark on it so I can’t set the dial to the 12 o’clock position. So any advice you may have on fixing this E12 error code would be greatly appreciated.

    Regards
    Matt

  4. Kerrigan Deane says : Reply
    February 10, 2017 at 7:34 pm

    We have just purchased a machine WMI 71641. Third time if using it and it finishes the cycle but all the while the water is running in the detergent draw. Any ideas please?

    • Paul Charmbury says : Reply
      February 14, 2017 at 1:42 pm

      jammed valve is my guess

      photo  
      Paul Charmbury
      Appliances Engineer
      youtube facebook google+ beer
    • Nathan says : Reply
      May 5, 2017 at 3:33 am

      Take the lid off (2 screws at back) carefully, start the machine and then gently squeeze the black tube from the offending valve, I’d it’s just a little stuck it’ll slowly shut on its own. Do this 3 or 4 times until it shuts on its own. I’d still faulting you’ll need a new valve.

  5. Mike w says : Reply
    February 14, 2017 at 7:01 pm

    Hi have a womb 8 series. Can’t open the door, now it has stopped washing. Actual door catch stays in when pressed and isn’t returning. Catch maybe broken? Have taken top off. Any idea how I can get the door open to see if it’s the catch or not. With power off will the machine door operating lock auto disengage, in case it’s that stopping it? At the end of a cycle you can hear a click, so think it’s disengaging?

  6. andrew says : Reply
    February 15, 2017 at 1:09 pm

    My washer does not have a start button so how do I carry out a self diagnostic check.
    Its a Beko 74155lw

  7. Jim says : Reply
    February 26, 2017 at 7:06 pm

    Hi Paul,

    I have a Beko 8kg 1400 rpm a++ WMB 81442 LW excellence washing machine, after doing the diagnostic test mode the only step that did not work was the anti-clockwise rotation, the error code that showed was 15:26 E18, can you tell from the error code what might be the issue and what parts would be required to fix it?

    Cheers

  8. Lesley says : Reply
    March 7, 2017 at 3:57 pm

    Hi Paul I have a beko washer and it keeps filling up with water on the pre wash draw any ideas please

  9. Lesley says : Reply
    March 7, 2017 at 5:15 pm

    After watching video I have tried that 1602 comes up both water draws fill but right hand draw Carries on filling even when on spin and drain any ideas please

  10. Uts123 says : Reply
    March 19, 2017 at 2:30 pm

    I have a WMB 71243 PTE, after i start it takes water in. then it starts to rotate and after about 1or 2 second it stops and just stays ther. If i pause it and play it again it will again start to rotate and stop after 2s. if i change the operatingmode, same thing will happen. I tried reading the diagnostic code and it showed E05. Any idea whats wrong there and how to get it right?? Thanx in advance.

  11. Roy Sweet says : Reply
    March 29, 2017 at 4:51 pm

    Hi Paul
    Our WME7267S seems OK throughout the Test mode, except for step 8. when the fabric conditioner Compartment is not siphoning correctly. Appreciate your thoughts on this problem. It seems the conditioner has not been working for some time, however, my wife says that it did perform when she used the Wool setting two days ago.
    Thanks
    Roy

  12. Hentman says : Reply
    March 31, 2017 at 8:19 pm

    Hi!

    BIG BIG thanks for this site and the Videos. Had a Code E18 and went through the error Analysis. No pump function. I diassembled everything as instructed and voila! Bck in Business.

    Again, thank you very much.

    Frank

  13. Lisa says : Reply
    April 5, 2017 at 3:38 pm

    I have beko washing machine wmb81445 lw with a code f13. Please can you advise
    Many thanks
    Lisa

  14. Narendra says : Reply
    April 10, 2017 at 8:12 am

    Hi, Paul,
    I have WMB17241 machine, what is the error for error code E17? and how to fix the problem?

  15. Jim says : Reply
    May 7, 2017 at 1:58 am

    Hi Paul i have a WMY9048LB1 and I’m trying to do what the video says but this model is a full electric version. Is their anything else i can do? The machine doesn’t start working at all and all it does is makes a funny ticking noise and after a few minutes it switches off.

  16. SHIJU THANDASSERY says : Reply
    May 11, 2017 at 4:39 pm

    hi mr paul i have BEKO WMB71241 , MY MACHINE AFTER WASHING FINISHED DOOR WONT OPEN AND IF TRYING TO WASH AGAIN ITS WORKING AND AND NOT POSSIBLE TO OPEN DOOR . I TRIED TO PUT IN TEST MODE , SHOWING 15 20 AND FULL SCREEN APPEARS , THEN HANGS . NO OTHER FUNCTIONING PLEASE SUGGEST ME A SOLUTION

  17. Julie says : Reply
    May 16, 2017 at 8:44 am

    E11 code but machine filling with water after i put it on drain and now won’t stop filling up. Its nearly at the top. I have turned the machine off but its now almost completely full of water (no clothes) what do i do next?

  18. barbara bretherton says : Reply
    June 15, 2017 at 10:00 am

    I have a Beko WMB71642W which starts to fill and after a few seconds stops and drains then shows End. Have done self diagnostic which all seems OK but showing error code 09. Any ideas

  19. Richard says : Reply
    July 19, 2017 at 12:28 am

    Hello. Many thanks for your thread. My Beko WMB series machine has a flashing temperature and start icon after being turned on and won’t start a washing cycle. There are no fault codes. I can enter diagnostics mode, as per your instructions, but after entering diagnostics mode it won’t cycle through the different diagnostic tests when I press ‘start/pause’.

  20. John Young says : Reply
    July 31, 2017 at 3:31 pm

    My washing machine will not start when load it and program it and close the door I have to kick the door to start it sometimes a couple of times.help please

« Older Comments
Newer Comments »
24h technical help answers

Questions on faults in the comments will not be answered. Please use the contact us form instead.





 
TOP