Indesit Vented Tumble Dryer ISL60V It gets hot but only runs for a few minutes then stops the cycle?
It has been working fine and I replaced a thermostat in it 4 years ago, but it now ends the cycle too soon.Thanks
Arthur Wright
I will try and help with your Indesit Vented Tumble Dryer ISL60V problem
Good morning this could be a problem with the machine overheating or one of the thermostats may be cutting out, or it could be the circuit board breaking down after a period of time it is a very hard one to diagnose when I'm not in front of the machine you will need to test the thermostat while under load to see if any of them are cutting out, remember there is a forward thermostat which is part number 261 in the diagram below it is also possible that the motor may be cutting out, there are plenty of useful videos on the website to assist you in your repair and there is a full exploded diagram of your model of the machine below and a full list of parts underneath that if you need any further assistance feel free to contact me
If you want to support the site please mark us to your favourites, also I would be grateful if you would subscribe to our social media channels as this really helps my site and keeps us going.
YouTube. http://www.youtube.com/user/howtorepair
Facebook. https://www.facebook.com/how.to.repair.appliances
And if we really helped you save money you can always click on the Buy Paul a Beer page
Common Indesit Vented Tumble Dryer ISL60V faults with links to the right repair guide
I have included a lot of videos in the links below on these tumble dryers to assist you in repairing your tumble dryer; I have also included an exploded diagram of your machine with all the parts that you need listed below that just click on the relevant and it will take you to a search result
- No heat
This is the most common fault on tumble dryers.
Vented dryers: this can be a fault with the thermostats, heater, or on some occasions, it might be the timer or the relay on the printed circuit board.
Condensor dryers: this might be any of the above but you also have a condenser plate that collects the water and then is either pumped to the collection tray or flows into a tank. Check pump unit and float switches.
Heat pump dryers: these are much more complicated they use a refrigeration prosses to heat the cloths and use the cooling side to condense the water for collection. Check compressor is running, check NTC sensors and check filters, and also that it has the right amount of refrigeration gas (normally only done by an engineer)
- Drum not turning
This will stop the dryer from drying. You may have to replace a faulty belt or in other cases, look at the motor, motor capacitor, or the jockey wheels. Again there are relays on printed circuit board types that can go faulty.
- Not starting
Whilst, not a common problem, you may have a faulty door switch, starter relay if fitted, or can be start button or PCB.
- Noisy Machine
This is usually caused by faulty bearings, jockey wheels or worn felt pads. The motor can get dust build up in the bearings, also the fan blades can distort in shape and make noise rubbing the housing.
- Water leaks.
This can be a simple as the water tank (in a condenser tumble dryer) has not been emptied, or not placed back into the housing correctly. The condenser plate can need cleaning. The pump unit might not be working. Or the ducting system can be clogged with fluff etc. See servicing tumble dryer.
- Tumble dryer reports a fault code or error code.
Error codes can be on the display or given in certain lights flashing sequences. Tumble dryer fault codes are not universal but may only point you or an engineer in the right direction they are not 100% accurate they are only that for guidance. Your owner’s manual may help you identify the problem and even suggest a fix. In other cases, you’ll need an engineer to trace the fault. Don’t be tempted to ignore a fault code, even if the dryer seems to be functioning normally. Some codes are ‘early warning signs’ and fixing the machine at an early stage could save you time and money in the long run.Contact us with the full model number and detailed description
-
Hotpoint Indesit Tumble dryer not heating Replacing element
-
Tumble dryer noisy Hotpoint
-
How to replace tumble dryer belt on Hotpoint, Indesit, Ariston, Creda & Proline
-
Hotpoint Creda tumble dryer how to fit front felt bearing. Part 1
-
Error fault codes for Ariston, Hotpoint Indesit, Scholtes washing machines
-
Condenser Tumble Dryer how to replace the pump unit.
-
How to service a Condenser Tumble Dryer pump unit.
-
How to replace a Tumble Dryer fixed drum Riveted Drum shaft
Match your part for Indesit Vented Tumble Dryer ISL60V and use reference number in list below and click on the link to your part
Reference | Part Number | Description |
---|---|---|
101 | C00207846 | CONSOLE |
103 | C00114672 | TIMER KNOB |
107 | C00114000 | OPTION BUTTON |
125 | C00095621 | SCREW 8 X 1/2 NON ROHS |
125 | C00116323 | TABLE TOP WHITE |
147 | C00114001 | START BUTTON |
152 | C00114002 | ON OFF SWITCH CAP |
153 | C00097012 | PILOT LAMP LENS VERTICAL |
155 | C00203127 | LIGHT GUIDE |
157 | C00193844 | DISPLAY USER INTERFA CE |
201 | C00116319 | PLINTH COVER |
205 | C00207652 | Tumble Dryer Fluff And Lint Filter |
207 | C00095624 | Tumble Dryer Vent Hose |
209 | C00142613 | Tumble Dryer Drum Front Seal |
209 | C00276750 | SEAL AIR DUCT 16MM VENTED DRUM FRONT |
210 | C00112210 | FRONT PANEL |
210 | C00142144 | FRONT PANEL |
212 | C00112211 | Tumble Dryer Door Seal |
213 | C00255284 | Tumble Dryer Door Bearing Pad |
215 | C00141694 | Tumble Dryer Door Lock |
215 | C00142615 | DOOR INTERLOCK SWITC H (TD) |
221 | C00039537 | Washing Machine & Tumble Dryer Screw |
221 | C00116335 | DOOR TRIM FRONT |
222 | C00116336 | Tumble Dryer Rear Door Trim |
223 | C00112192 | Tumble Dryer Door Glass |
223 | C00113819 | SEAL DOOR BOWL |
224 | C00095987 | HINGE |
225 | C00112277 | DOOR HINGE PLATE |
228 | C00112214 | DOOR HANDLE |
228 | C00039537 | Washing Machine & Tumble Dryer Screw |
233 | C00142619 | Tumble Dryer Door Latch |
233 | C00195678 | V.AU.7SPX6 T.PIA.ZIN |
257 | C00095629 | COVERING BLANK |
257 | C00250726 | SCREW NO6 X 3/8 ROHS |
257 | C00097675 | STAT EARTH BRACKET |
257 | C00113821 | WATER SHIELD |
257 | C00112215 | AIR DUCT |
257 | C00261899 | FRONT AIR DUCT |
257 | C00278295 | AIR DUCT 14MM SEAL R IB GREY |
261 | C00113822 | THERMISTOR FRONT ELTH |
261 | C00142702 | THERMISTOR FRONT TOD |
401 | C00122256 | SCREW |
401 | C00112148 | BASE PANEL(WHEELS) |
401 | C00142908 | BASE PANEL(FEET) |
401 | C00252668 | BASE SUPPORT BRACKET |
401 | C00292281 | BASE (WASHERS NOT RE QUIRED) |
403 | C00095592 | WHEEL AXLE |
403 | C00122256 | SCREW |
404 | C00111360 | WHEEL |
404 | C00142439 | Tumble Dryer Foot |
405 | C00282296 | Tumble Dryer Motor |
408 | C00119849 | Tumble Dryer Capacitor |
408 | C00199432 | CAPACITOR 7UF RHOS ( TD) |
408 | C00275351 | CAPACITOR 9.5UF |
408 | C00279463 | CAPACITOR 9UF |
409 | C00112153 | IMPELLER INNER |
410 | C00116327 | IMPELLER OUTER |
413 | C00113038 | Tumble Dryer Drum Shaft |
413 | C00305794 | DRUM SHAFT KIT (RIVE TED DRUM PLATE) |
420 | C00383247 | VENTED (4MM RIVET) REAR PANEL KIT |
421 | C00145707 | Tumble Dryer Drive Belt |
422 | C00383262 | Tumble Dryer Drum |
423 | C00122256 | SCREW |
423 | C00113825 | FOAM PAD REAR PANEL |
423 | C00260451 | REAR PANEL BRACE |
423 | C00383247 | VENTED (4MM RIVET) REAR PANEL KIT |
424 | C00113862 | DRUM REAR BEARING SQUARE SHAPE |
424 | C00142628 | Tumble Dryer Rear Drum Bearing |
424 | C00250889 | SCREW M4X10 |
425 | C00142631 | DRUM SHAFT COLLAR |
426 | C00095551 | Tumble Dryer Drive Pin |
427 | C00095572 | M3 X 6 TAPTITE SCREW |
427 | C00199479 | Tumble Dryer Drum Earth Strip |
428 | C00095565 | Tumble Dryer Rear Bearing Fixing Bracket |
428 | C00250832 | 1/8 RIVET |
429 | C00122256 | SCREW |
429 | C00141697 | ADAPTOR-VENT HOSE |
430 | C00113839 | BUFFER PAD |
430 | C00116602 | HEATER 2.2KW VENTED ELTH NTC |
430 | C00257622 | HEATER ASSY 2200W VNTD TOC IN NEUTRAL |
430 | C00258798 | HEATER TOD THERMISTO R |
430 | C00258811 | HEATER(ONE SHOT+ CYC LING+ NTC ELTH) |
432 | C00208317 | STAT KIT WITH TOD (B LACK) NTC DBK |
432 | C00208318 | STAT KIT-WITH ELTH ( WHITE) NTC DBK |
432 | C00262243 | Tumble Dryer Thermostat |
442 | C00095556 | CABLE CLAMP/GROMMET |
442 | C00250833 | NO7 HILO POZI SCREW |
445 | C00380932 | MAINS CABLE AND PLUG 1.8M BLACK |
448 | C00095585 | MAINS CON AND SUPPRE |
448 | C00250888 | SCREW |
450 | C00122256 | SCREW |
450 | C00112184 | SIDE PANEL |
451 | C00116328 | HEATER COVER VENTED (DBK) |
452 | C00095553 | REAR BEARING COVER METAL |
452 | C00122256 | SCREW |
452 | C00118929 | REAR BEARING COVER PLASTIC |
455 | C00161366 | HANDBOOK |
463 | C00112186 | DRUM LIFTER LONG |
463 | C00250835 | SCREW 5 X 23 |
463 | C00286905 | Tumble Dryer Small Drum Lifter |
465 | C00113830 | THERMISTOR REAR ELTH |
465 | C00143511 | THERMISTOR REAR TOD |
466 | C00202842 | EEP EVOII BLANK EVO 2 |
466 | C00207857 | EEPROM ISL60V (UK) |
466 | C00208156 | EEP ISL60V UK NEWSEN |
466 | C00208320 | EEPROM ISL60V VE07 TOD |
466 | C00195647 | EEPROM ISL60VUK EVO11 SW 28306310014 |
466 | C00269466 | MODULE A1 EVO SW4.05 .05 NO SKT (TD) |
466 | C00272309 | SMARTCARD ISL60V 283 06310002 |
466 | C00272365 | SMARTCARD ISL60V 283 06310006 |
466 | C00272414 | SMARTCARD ISL60V 283 06310007 |
466 | C00272416 | SMARTCARD ISL60V 283 06310014 |
468 | C00113836 | LIFTER SENSING |
468 | C00286905 | Tumble Dryer Small Drum Lifter |
469 | C00113838 | INSULATOR BAND |
469 | C00113837 | SENSING BAND |
470 | C00113816 | BRUSH SUPPORT |
470 | C00113817 | SENSING BRUSH |
471 | C00122256 | SCREW |
471 | C00112188 | COVER SERIAL PORT |
471 | C00112189 | WATER SHIELD |
558 | C00113830 | THERMISTOR REAR ELTH |
558 | C00143511 | THERMISTOR REAR TOD |
999 | C00097686 | WALL WINDOW VENT KIT |
999 | C00222676 | SWITCH REMOVAL TOOL |
999 | C00222677 | BUTTON REMOVAL TOOL |
999 | C00149418 | Tumble Dryer Vent Hose & Adaptor |
999 | C00221756 | SERVICE MANUAL |
999 | C00142716 | BELT FIT TOOL TD |