Beko DCU 9330W Tumble Dryer I’ve got a dryer that hums and wouldn’t spin
Hi, I've got a dryer that hums and wouldn't spin, just seen your video describing the capacitor fault and thought I'd order one from you to thank you for the video help! I have a Beko DCU 9330W and I can't see a capacitor listed for it on your listings. Could you point me to the correct one?Kind regards
Simon
I will try and help with this problem Beko DCU 9330W Tumble Dryer
If you'll tumble dryer will not turn and you have a humming sound this is a good indication that your'll capacitor has gone I have put an exploded diagram of your machine below and a video to assist you I've also included a link to the capacitor that you'll require
If you want to support the site please mark us to your favourites, also I would be grateful if you would subscribe to our social media channels as this really helps my site and keeps us going.
YouTube. http://www.youtube.com/user/howtorepair
Facebook. https://www.facebook.com/how.to.repair.appliances
And if we really helped you save money you can always click on the Buy Paul a Beer page
Common Beko DCU 9330W Tumble Dryer faults with links to the right repair guide
I have included a lot of videos in the links below on these tumble dryers to assist you in repairing your tumble dryer; I have also included an exploded diagram of your machine with all the parts that you need listed below that just click on the relevant and it will take you to a search result
- No heat
This is the most common fault on tumble dryers.
Vented dryers: this can be a fault with the thermostats, heater, or on some occasions, it might be the timer or the relay on the printed circuit board.
Condensor dryers: this might be any of the above but you also have a condenser plate that collects the water and then is either pumped to the collection tray or flows into a tank. Check pump unit and float switches.
Heat pump dryers: these are much more complicated they use a refrigeration prosses to heat the cloths and use the cooling side to condense the water for collection. Check compressor is running, check NTC sensors and check filters, and also that it has the right amount of refrigeration gas (normally only done by an engineer)
- Drum not turning
This will stop the dryer from drying. You may have to replace a faulty belt or in other cases, look at the motor, motor capacitor, or the jockey wheels. Again there are relays on printed circuit board types that can go faulty.
- Not starting
Whilst, not a common problem, you may have a faulty door switch, starter relay if fitted, or can be start button or PCB.
- Noisy Machine
This is usually caused by faulty bearings, jockey wheels or worn felt pads. The motor can get dust build up in the bearings, also the fan blades can distort in shape and make noise rubbing the housing.
- Water leaks.
This can be a simple as the water tank (in a condenser tumble dryer) has not been emptied, or not placed back into the housing correctly. The condenser plate can need cleaning. The pump unit might not be working. Or the ducting system can be clogged with fluff etc. See servicing tumble dryer.
- Tumble dryer reports a fault code or error code.
Error codes can be on the display or given in certain lights flashing sequences. Tumble dryer fault codes are not universal but may only point you or an engineer in the right direction they are not 100% accurate they are only that for guidance. Your owner’s manual may help you identify the problem and even suggest a fix. In other cases, you’ll need an engineer to trace the fault. Don’t be tempted to ignore a fault code, even if the dryer seems to be functioning normally. Some codes are ‘early warning signs’ and fixing the machine at an early stage could save you time and money in the long run.Contact us with the full model number and detailed description
Match your part for Beko DCU 9330W Tumble Dryer and the use reference number in list below and click on the link to your part
Reference | Part Number | Description |
---|---|---|
1 | 2974500100 | TOP PLATE |
10 | 2976600400 End Of Life | FRONT DOOR ASSEMBLY |
1005 | 2962510800 | CONDENS PUMP |
1005 | 2962510600 End Of Life | CONDENS PUMP |
1044 | 133000001 | WASHER 12x18x1 DIN 988.. |
1045 | 160200200 | ZEEGER 9x1 DIN 6799 DRCS68 |
1046 | 2973900500 | REAR PANEL ASSY |
1077 | 492204404 | PULLEY ASSY FOR SERVICE-ARES |
1087 | 2963110100 | HOSE AND CABLE HOLDER |
1098 | 2962630100 | FAN COVER - COOLING |
12 | 2962120100 | INNER DOOR_(ARES_ARC1_WITHOUT_SWITCH) |
1209 | 2969500300 | LOCK BODY ASS |
1244 | 2979290100 | POMP COVER |
1246 | 2971703502 | CABLE ASSEMBLY |
1248 | 2960910300 | SILICONE GASKET |
1249 | 2977904200 | CABLE ASSEMBLY |
1256 | 2973100100 | SHAFT-FRONT BEARING ASSY |
1259 | 2972300100 | FILTRE CASETTE ASSY |
1260 | 2962960100 | OVERFLOW FLOAT |
1271 | 2962690100 | AIR GUIDING PART |
1279 | 2968300300 | BEARING SENSOR COVER ASSEMBLY |
1287 | 2960150100 | RUBBER STOPPER |
1290 | 2962590100 | DOOR GASKET |
1295 | 2963120400 | MOTOR BRACKET CLAMP (PLASTIC) |
1303 | 2962450100 | TANK GUIDE (TOP_60CM) |
1306 | 2961390200 | TANK GUIDE BARRIER |
1313 | 2705810300 | PT SCREW (3_5x8) |
1314 | 2987800100 | ROUTER GROUP AIR OUTLET |
1377 | 2965200300 | MAIN CABLE ASSEMBLY |
1390 | 9002900200 | COUNTERSUNK HEAD SCREW (PT-4X14) |
1398 | 2951780300 | DELTA PT VIDA 50x26 WN 5454 HB |
1399 | 2962950100 | NTC GASKET |
14 | 2962170200 | HINGE |
1401 | 2963210100 | MOTOR SHAFT SEAL |
1417 | 2705810400 | PT SCREW (3_5x14) |
1440 | 2961690100 | ADJUSTABLE PLASTIC FOOT |
1451 | 2963180200 | BACK COVER FELT |
1453 | 2953741500 | SINGLE ADHESINE EPDM FOAM |
1454 | 2963090100 | AIR GUIDING GASKET |
1455 | 2962810100 | SIDE WALL PIN |
1457 | 2971900200 | NTC (EPCOS_12K) |
1457 | 2971900300 | NTC |
1457 | 2971900500 | DOOR NTC |
1459 | 2969900200 End Of Life | ROLLER ASSY |
1460 | 2951261000 | POMP WATER TANK HOSE. |
1462 | 2951260800 | POMP WATER TANK HOSE. |
1463 | 2951260900 | POMP WATER TANK HOSE. |
1465 | 2951261100 | POMP WATER TANK HOSE. |
1466 | 9003272000 | PLASTIC SCREW (DIAMETER 4x10) INOX |
1469 | 100700120 | SCREW (B4.2*9.5 DIN 7982-H) |
1471 | 2953741100 | SINGLE ADHESINE EPDM FOAM. |
1473 | 2962390100 | LOCK MOUTH |
1478 | 2963420100 | WATER COLLECTOR |
1481 | 2961720300 | COOLING AIR INFLOW RECTIFIER |
1482 | 2963240100 | COOLING AIR INFLOW FELT |
1483 | 2963250100 | COOLING AIR OUTFLOW FELT |
1484 | 2961990100 | SIDE SUPPORT (RIGHT 60CM) |
1485 | 2962010100 | Side support left 60CM |
1486 | 2974470100 | SHAFT DRUM COVER |
1486 | 2974470300 | SHAFT DRUM COVER |
1486 | 2974470700 | SHAFT DRUM COVER SHC ALS |
1489 | 2962290100 | DOWN HINGE GUIDE |
1490 | 2962310100 | UP HINGE GUIDE |
1492 | 2962460100 | TANK GUIDE CAP |
1495 | 2964010100 | PANEL FLAMABILITY PART |
1497 | 9003271700 | PLASTIC SCREW |
1506 | 9001231300 | PLASTIC CLAMP 250 mm |
1507 | 2951261300 | POMP WATER TANK HOSE. |
1540 | 2966930100 | SMART LAMP |
1542 | 2966040100 | CARD HOLDER (SMART-LAMP) |
1587 | 2966990100 | CABLE TRAY |
1588 | 2967080100 | RACEWAY SOCKET GUARD |
166 | 2971603100 | MAIN CABLE ASSEMBLY |
169 | 2970445400 | POWER SUPPLY CORD |
1741 | 2971900100 | NTC |
18 | 2973500100 | ADJUSTABLE PLASTIC FOOT ASSY. |
180 | 2964170100 | ON_OFF SWITCH(ROLD (+) FORM) |
186 | 2961561501 | ELECTRONIC PCB ASSY.(CNDU MLCD INVERTED) |
189 | 491500303 | POLY-V 285 H 4 MA BELT |
197 | 2963749020 | DRAWER PANEL ASS. |
200 | 2975309017 | PANEL ASSEMBLY |
2013 | 2970540100 | POWER PLUG HOLDER |
203 | 2976701900 | PROGRAMME KNOB BUTTOM_ASSY |
33 | 9001230800 | PLASTIC CLAMP 152 mm |
339 | 2976500500 | OUTER RING DOOR ASSY |
341 | 2962150100 | LOCK HOOK |
374 | 265900012 End Of Life | OVEN LAMP 15 W-230 V |
401 | 2963580100 | FRONT PANEL |
4210 | 2974870200 | INTERFERENCE FILTER |
43 | 2960310463 | USER'S MANUAL. |
468 | 2963710100 | ON OFF BUTTON (TIP02+ARC 734 MAVI) |
48 | 2971400400 | DRUM ASSEMBLY |
481 | 2827190400 | Rotary switch |
581 | 2966980100 | HEATER CABLE GUARD |
583 | 2705870100 | SELF LOCKING CABLE HOLDER |
584 | 2962860100 | DRUM LIFTER |
59 | 2962470200 End Of Life | ELASTIC POLY-V BELT. 7PH 1956 |
63 | 2963140100 | DRYER MOTOR |
632 | 2962160100 | HINGE BUSHING |
65 | 2970101500 | HEATER ASSY |
653 | 2807961400 | CAPACITOR (ARCOTRONICS 9 uF) |
750 | 2963790100 | PCB HOLDER |
804 | 2973800100 | REAR DRUM TIGHTNESS PLATE ASSY |
804 | 2973801100 | REAR DRUM TIGHTNESS PLATE ASSY |
804 | 2973800700 | REAR DRUM TIGHTNESS PLATE ASSY |
822 | 2963540100 | KICK PLATE - LEFT |
826 | 2972900800 | HEATER COVER ASSY |
826 | 2972900500 | HEATER COVER ASSY |
827 | 2962020100 | UPPER BEAM |
8318 | 2002370900 | HOSE CLAMP (Ø 16.4) |
8320 | 100601520 | SHEET METAL SCREW (B4.2X13 DIN 7981-H) |
834 | 2959400200 | REAR BEARING ASSEMBLY |
8365 | 2828040300 | DRAIN HOSE HOLDER |
8384 | 9003270100 | PLASTIC SCREW |
8385 | 9003270400 | PLASTIC SCREW (4_10) |
8386 | 9003270500 | PLASTIC SCREW (4_12) |
8392 | 9003610300 | sheet metal screw(B4_2x9_5-perforated) |
8397 | 9003610100 | SHEET METAL SCREW(B4_2x9_5-perforated) |
8398 | 9003670100 | SCREW FOR PLASTIC -4.5x12 |
8403 | 9003860300 | SHEET METAL SCREW |
8413 | 120800120 | FIBERED_NUT_M6X1_DIN_985 |
8415 | 2826510200 | DOWEL PLASTIC CLAMP |
8419 | 2963340100 End Of Life | WASHERED NUT (M6x1) |
842 | 2960190100 | CABLE HOLDER |
8422 | 2951580400 | COUNTERSUNK HEAD PT SCREW (4.5x12) |
8428 | 2971870100 | MX10 RYSB PERFORATED SCREW |
843 | 2962440100 | WATER TANK (UP_8KG) |
8434 | 2951780400 | DELTA PT SCREW |
844 | 2961290200 | DISCHARGING FUNNEL |
845 | 2963530100 | KICK PLATE - RIGHT |
846 | 2962680100 | CONDENSER SNAPPER |
847 | 2978720200 | PLASTIC CHASIS ASSY |
856 | 2974940100 | HINGE PIN HOLDER (PLASTIC) |
857 | 2963150100 | SPRING |
861 | 2963330400 | FRONT SELING FELT |
865 | 2962650100 | LAMP COVER |
877 | 2971100100 | PROCESS FAN ASSY |
888 | 2951060600 | MICRO SWITCH |
888 | 2951060700 End Of Life | MICRO_SWITCH |
891 | 2961680100 | COOLING FAN |
906 | 2961190200 | SPECİAL WASHER (8,1*17*1,5) |
921 | 2980100200 | CONDENDER ASSY. (60CM) |
921 | 2980100100 | CONDENDER ASSY. (60CM) |
932 | 2961961000 | SIDE PANEL |
985 | 2954700100 End Of Life | Micro Switch Ass. |
985 | 2954700400 | Micro Switch Ass. |