Hoover DX C10TCE-80 Tumble dryer Error code e21
Hi, hope you may be able to help. I am getting e21 flashing, my husband has checked for blockages and cleaned it out but it’s still flashing. Could you suggest if we need to replace a part please?
Dena Moore
I will try and help with this problem Hoover DX C10TCE-80 Tumble dryer
Here is a list of all the error codes with this tumble dryer.
E21 is normally to do with the heater check all thermostats and heater element also make sure there are no blockages in the pump
Heater control relay on the “cuore” electric module is not working. High temperature has
been reached – Thermo Fuse worked. Check the thermo Fuse, and the wiring. Check that
both the ventilation circuit and ventilation ducts are clean and duct is not obstructed.
Replace the “cuore” electric module only in the case that the heater command relay is
Faulty or replace the heater relay on the pcb
I have added some videos to assist you below, I there's a full list of parts which are available for this machine just cut and paste the part you require into our search box and if there are any available it will show
Other error codes with Hoover DX C10TCE-80 Tumble dryer
E03 Tank is full of water and has to be emptied.
E05 Front NTC sensor is either short circuit or open circuit. Check front NTC sensor and/or
wiring.
E07 Alarm, filter occluded, This error can only appear after the end of a cycle. The filter is
occluded because of fluff presence, the correct ventilation is not allowed. Clean the filter.
E08
Thermo fuse intervention. Replace the thermo fuse and check that ventilation circuit is
clean, check the wiring.
E10 Missing communication between "Cuore" Electric Module and Display Electric Module and/or
Wiring.
E11
In the rear part of condenser the temperature is too high. Check that all ventilation ducts
are clean, check that ventilation system is working well. Check the condenser, the motor,
the fan could be broke/blocked.
E12 Pressure switch doesn’t work. Check the pressure switch and/or wiring. Check that the air
trap is clean.
E13 Compressor NTC Probe is either Short Circuit or Open Circuit. Check the compressor NTC
probe and/or wiring.
E14
Rear NTC Probe is either Short Circuit or Open Circuit. Check the rear NTC probe and/or
wiring.
E15 Main board not programmed. Program the main board.
E19
It is not possible to use NFC tag for any actions until the next POWER ON/OFF. (switch off
and switch on)
E21
Heater control relay on the “cuore” electric module is not working. High temperature has
been reached – Thermo Fuse worked. Check the thermo Fuse, and the wiring. Check that
both the ventilation circuit and ventilation ducts are clean and duct is not obstructed.
Replace the “cuore” electric module only in the case that the heater command relay is
faulty.
E22
Compressor control relay on the “cuore” electric module is not working. Check the
compressor and compressor wiring/connections. Replace the “c
If you want to support the site please mark us to your favourites, also I would be grateful if you would subscribe to our social media channels as this really helps my site and keeps us going.
YouTube. http://www.youtube.com/user/howtorepair
Facebook. https://www.facebook.com/how.to.repair.appliances
And if we really helped you save money you can always click on the Buy Paul a Beer page
10 | 40009129 | timer knob |
31b | 40011397 | Control panel with Sensor |
48 | 40010677 | R/H side frame |
48a | 40010678 | L/H side frame |
49 | 40004597 | Top rear frame |
49g | 41041380 | Trade mark plate |
51 | 40004601 | Work top |
60 | 40009040 | Hinge |
63 | 40006231 | Door glass |
67 | 40010996 | Door with trim |
77 | 40004062 | Rear panel |
77 | 40012171 | Rear panel |
79 | 40002885 | Foot |
82 | 40009192 | Door panel |
88 | 40008589 | Front panel |
131a | 92470020 | Hose clip |
152a | 40010529 | Light guide support |
156 | 41039164 | Capacitor 7 MF |
157 | 40010653 | Harness |
157 | 40012503 | Harness |
161 | 40005021 | Pump |
164 | 91200489 | Anti jamming filter radio |
171 | 40008460 | Main motor |
202 | 40009120 | Drum |
202 | 40011928 | Drum |
205 | 40006362 | Drum shaft assy |
218 | 3210179 | Bearing |
229 | 24721202 | Circlip |
230 | 40004306 | Bearing clamp |
231a | 40007401 | Pipes holder |
271 | 40005393 | Door gasket |
280 | 40009775 | Hose clip |
292 | 40001012 | Drive belt |
292 | 40012264 | Drive belt |
318b | 49040749 | Electronic control PCB - NFC -Programmed |
318c | 49041739 | Electronic NFC pcb - Not programmed |
442 | 40009278 | Fan |
442a | 40009379 | Rear fan |
443 | 41037151 | Thermostat |
444 | 40012558 | Duct fun |
445 | 40012556 | Nozzle Cond. Recovery |
445a | 40012557 | Nozzle Cond. Recovery Seal |
448 | 40005010 | Heater |
448 | 40013366 | Heater |
461h | 41014595 | drying probe seal |
491c | 91200201 | Mains cable x UK |
494d | 40010528 | Light Guide - Digital Display |
520 | 40006928 | Door coupler |
607 | 40006220 | Pin for hinge |
631 | 40006586 | Stopper |
643a | 41041381 | Handle plate - profile |
647 | 40008382 | Water condenser |
654 | 40003802 | Thermostat gasket |
671 | 3610428 | Washer |
690 | 40006246 | Rear sealing felt |
690a | 40004577 | Rear cover seal |
690c | 40010756 | Seal motor/water duct |
696 | 40006820 | Heater support |
697 | 40003226 | Heater support disk |
706 | 40010765 | Front ring assembly |
706 | 40012494 | Front ring assembly |
707 | 40005584 | Filter for carter |
727 | 40004816 | Gasket |
728 | 40006251 | Gasket |
731b | 40012561 | Flow pipe (Water drain) |
731c | 40009075 | Water Delivery Pipe |
734 | 40012701 | Container |
734 | 40012545 | Container |
738 | 40004817 | Gasket |
745 | 40009144 | Kickplate assy |
748 | 3320032 | Tube |
755 | 40007362 | Cover |
755a | 40007363 | Fan insert |
756 | 23715194 | Spring |
757 | 40003315 | Gasket |
763b | 40003319 | Water rear duct gasket |
763d | 40008360 | Reservoir top cover |
764 | 40004815 | Gasket |
766 | 40009648 | Water container assy |
766b | 40004928 | Water container front cover |
777 | 40004157 | Heater gasket |
797 | 40004610 | Beltightening pulley |
799 | 40001026 | Belt tighteningb spring |
804 | 40009167 | Hinge fixing upper bracke |
819 | 40009121 | Drum scowel |
822 | 40010003 | Innerdoor assy |
826 | 40004091 | Door hook |
835 | 40004307 | Drum support wheels |
840 | 40010626 | Float assy |
840a | 40008358 | Floating |
840b | 41041353 | Microswitch |
998a | 40011399 | Eeprom File NFC |
999 | 41045051 | Electrical diagram |
1004 | 40005153 | Flow restrictor |
1017 | 41022106 | NTC probe |
1026 | 40007831 | Front felt |
-
Tumble dryer not heating Hoover Candy diagnosing fault and repair
-
Hoover Candy Tumble dryer drum not turning and belt ok faulty capacitor
-
Hoover Candy Tumble dryer all lights flashing error fault code
-
Hoover VHV 680C Tumble Dryer Faulty mains switching relay on control board
-
Tumble dryer printed circuit board heater relay faults