FORGOT YOUR DETAILS?

AAH, WAIT, I REMEMBER NOW!

Hoover Tumble Dryer DX C9TCE-80 Dynamic Next Trips RCD as soon as switched on at socket

by / Tuesday, 29 December 2020 / Published in

RCD tripped taking out all of the downstairs power while dryer was running.Process of elimination pointed at dryer. As soon as I plug in and switch on the RCD goes again. Could it be a mains filter? If so, where is it?PS, I’m a spark by trade.

Simon Adamson

Paul answers

I will try and help with this problem Hoover dx c9tce-80 Condenser Tumble Dryer

it is possible that it could be the electrical filter at the back right-hand side of the machine, but from experience with these tumble dryers it is usually damp around the heater area this can cause the element to trip the rcd, if you have a mega or an insulation tester you will be able to isolate the problem, but if you do not it will be a process of elimination you could try disconnecting the heater and seeing if it starts, if it is not the heater then you may have a direct short from the motor or some other electrical component, I have included an exploded diagram of your machine with all the parts listed below I have also included some videos to assist you in your repair

 

 

 

If you want to support the site please mark us to your favourites, also I would be grateful if you would subscribe to our social media channels as this really helps my site and keeps us going.

YouTube. http://www.youtube.com/user/howtorepair
Facebook. https://www.facebook.com/how.to.repair.appliances
And if we really helped you save money you can always click on the Buy Paul a Beer page

 

Hoover Tumble Dryer DX C9TCE-80 Error codes and fault codes

Presently available error codes for the SKYLANDER models range

Cuore NFC electric module
ERROR CODE MOST PROBABLE REASON FOR THE ERROR CODE
E03 Tank is full of water and has to be emptied.
E05 Front NTC sensor is either short circuit or open circuit. Check front NTC sensor and/or
wiring.
E07 Alarm, filter occluded, This error can only appear after the end of a cycle. The filter is
occluded because of fluff presence, the correct ventilation is not allowed. Clean the filter.
E08
Thermo fuse intervention. Replace the thermo fuse and check that ventilation circuit is
clean, check the wiring.
E10 Missing communication between "Cuore" Electric Module and Display Electric Module and/or
Wiring.
E11
In the rear part of condenser the temperature is too high. Check that all ventilation ducts
are clean, check that ventilation system is working well. Check the condenser, the motor,
the fan could be broke/blocked.
E12 Pressure switch doesn’t work. Check the pressure switch and/or wiring. Check that the air
trap is clean.
E13 Compressor NTC Probe is either Short Circuit or Open Circuit. Check the compressor NTC
probe and/or wiring.
E14
Rear NTC Probe is either Short Circuit or Open Circuit. Check the rear NTC probe and/or
wiring.
E15 Main board not programmed. Program the main board.
E19
It is not possible to use NFC tag for any actions until the next POWER ON/OFF. (switch off
and switch on)
E21
Heater control relay on the “cuore” electric module is not working. High temperature has
been reached – Thermo Fuse worked. Check the thermo Fuse, and the wiring. Check that
both the ventilation circuit and ventilation ducts are clean and duct is not obstructed.
Replace the “cuore” electric module only in the case that the heater command relay is
faulty.
E22
Compressor control relay on the “cuore” electric module is not working. Check the
compressor and compressor wiring/connections. Replace the “cuore” electric module only
in the case that the compressor command relay is faulty.

If you need any further assistance please feel free to contact me​. all the best Paul​.

photo  
Paul Charmbury
Appliances Engineer
youtube facebook google+ beer

Match your part for Hoover Tumble Dryer DX C9TCE-80 Dynamic Next and the use reference number in list below and click on the link to your part

Hoover Dx C9tce-80 Condenser Tumble Dryer

Reference Part Number Description
10 40009129 Timer/select. knob
31b 40011281 Control panel with Sensor
48 40010677 R/H side frame
48a 40010678 L/H side frame
49 40004597 Top rear frame
49g 41041380 Trade mark plate
51 40004601 Work top
60 40009040 Hinge
63 40006231 Door glass
67 40010996 Door with trim
77 40004062 Rear panel
77 40012171 Rear panel
79 40002885 Foot
82 40009192 Door panel
88 40008589 Front panel
131a 92470020 Hose clip
152a 40010529 Light guide support
156 41039164 Capacitor 7 MF
157 40010653 Harness
157 40012503 Harness
161 40005021 Pump
164 91200489 Anti jamming filter radio
171 40008460 Main motor
202 40009120 Drum
202 40011928 Drum
205 40006362 Drum shaft assy
218 03210179 Bearing
229 24721202 Circlip
230 40004306 Bearing clamp
231a 40007401 Pipes holder
271 40005393 Door gasket
280 40009775 Hose clip
292 40001012 Drive belt
292 40012264 Drive belt
318b 49040177 Electronic control PCB - NFC -Programmed
318c 49041739 Electronic NFC pcb - Not programmed
442 40009278 Fan
442a 40009379 Rear fan
443 41037151 Thermostat
444 40012558 Duct fun
445 40012556 Nozzle Cond. Recovery
445a 40012557 Nozzle Cond. Recovery Seal
448 40005010 Heater
448 40013366 Heater
461h 41014595 drying probe seal
491c 91200201 Mains cable x UK
494d 40010528 Light Guide - Digital Display
520 40006928 Door coupler
607 40006220 Pin for hinge
631 40006586 Stopper
643a 41041381 Handle plate - profile
647 40008382 Water condenser
654 40003802 Thermostat gasket
671 03610428 Washer
690 40006246 Rear sealing felt
690a 40004577 Rear cover seal
690c 40010756 Seal motor/water duct
696 40006820 Heater support
697 40003226 Heater support disk
706 40010765 Front ring assembly
706 40012494 Front ring assembly
707 40005584 Filter for carter
727 40004816 Gasket
728 40006251 Gasket
731b 40012561 Flow pipe (Water drain)
731c 40009075 Water Delivery Pipe
734 40012701 Container
734 40012545 Container
738 40004817 Gasket
745 40009144 Kickplate assy
748 03320032 Tube
755 40007362 Cover
755a 40007363 Fan insert
756 23715194 Spring
757 40003315 Gasket
763b 40003319 Water rear duct gasket
763d 40008360 Reservoir top cover
764 40004815 Gasket
766 40009648 Water container assy
766b 40004928 Water container front cover
777 40004157 Heater gasket
797 40004610 Beltightening pulley
799 40001026 Belt tighteningb spring
804 40009167 Hinge fixing upper bracke
819 40009121 Drum scowel
822 40010003 Innerdoor assy
826 40004091 Door hook
835 40004307 Drum support wheels
840 40010628 Float assy
840a 40008358 Floating
840b 41041353 Microswitch
998a 40011283 Eeprom File NFC
999 41045051 Electrical diagram
1004 40005153 Flow restrictor
1017 41022106 NTC probe
1026 40007831 Front felt

full list of spare parts for this model below

Our How-to-repair stores

Current page 1 Total pages 0

One Response to “Hoover Tumble Dryer DX C9TCE-80 Dynamic Next Trips RCD as soon as switched on at socket”

  1. Simon Adamson says : Reply
    December 29, 2020 at 2:53 pm

    Fantastic help/support from Paul.
    He answered my email and even gave me a call on a bank holiday over the festive season!
    Clear and sound advice lead to me sorting the problem at the first attempt.
    Brilliant!
    Enjoy the beer, Paul.
    Cheers!

24h technical help answers

Questions on faults in the comments will not be answered. Please use the contact us form instead.

TOP