How to replace Brandt washing machine carbon brushes.

by / Thursday, 27 March 2014 / Published in Motors, Washing machines




How to replace Brandt washing machine carbon brushes.

 

 

If your Brandt washing machine is not spinning or it is filling with water but the drum is not turning then it is a good chance that you Brandt carbon brushes have worn out.
To order your washing machine motor Carbon Brushes you will need your full model number (This is normally around the washing machine door frame on a sticker) and also your motor Type, written on the motor Label.

How-to-replace-Selni-motor-id-label-on-Blomberg-Brandt-Fagor-De-dietrich-Thomson-etc

 

replacing-Selni-motor-carbon-brushes-on-Blomberg-Brandt-Fagor-De-dietrich-Thomson-etc

Selni-motor-armature-on-Blomberg-Brandt-Fagor-De-dietrich-Thomson-etc

old-and-new-Selni-motor-carbon-brushes-on-Blomberg-Brandt-Fagor-De-dietrich-Thomson-etc




If your Brandt washing machine is not spinning or it is filling with water but the drum is not turning then it is a good chance that you Brandt carbon brushes have worn out.

This video will show you how to replace Brandt washing machine carbon brushes with a Selni motor, we are working on a Brandt but this guide is good for most makes that have a Selni motor

To take out a motor on a Brandt washing machine might sound scary, but it’s a surprisingly easy to replace and then fit the carbon brushes.

- Remove the back panel.

- Then you need to remove the washing machine belt that is attached to the motor and drum pulley.

- You will now need to remove the bolts that attach the motor to the washing machine drum.

- Release the motor of the drum brackets or lugs, be careful it’s heavy.

- Next you need to remove the old Brandt carbon brushes.

- You need to clean the armature up.

- Fit new Brandt carbon brushes according to the video instruction.

 

8 Responses to “How to replace Brandt washing machine carbon brushes.”

  1. Albert Vella says : Reply

    Thanks for your video I found it very useful. our machine ‘Blomberg’ was not spinning so checked the brushes and found out that needs to be replaced and now its working fine again. The brushes costs me 19euro. Keep posting such videos cause they are very useful.

    Regards
    Albert Vella
    Malta

  2. Rameshkumar M Solanki says : Reply

    Thanks for video of replace the carbon brush of front lode washing I gain very useful details.
    Ramesh

  3. Carole says : Reply

    After watching your video I now realise my indesit washer dryer needs a set of brush as my machine now stops spinning. It fills up and make the necessary sounds but does not spin. My machine model is IWDE77125S. can you recommend a set of brush that will fit my machine and if you have any in stock. Thanks

  4. br5ian says : Reply

    have just removed the motor and looked at the brushes, they both look ok but are a little black to touch, they don’t look scored or laminated, there was some black dust on the back of the rear panel when i removed it, the machine is a blomberg wnf 6221 and was bought new on 31/12/ 2015, it never has had that much use, never more than 4 times a week, is it likely to be the motor burnt out or the brushes?

  5. Moshe Nagar says : Reply

    Hello,
    I was looking on your Youtube “Oven Not Heating, Selector Switch Fault on Oven” (https://www.youtube.com/watch?v=L8DemKB6uSk). The presenter/tecnition have mentioned you can help on finding parts.
    I have De Dietrich (CX4744/4844) oven/coocker. I need to find a new Selector Switch – can you help find?
    Please advise.

24h technical help answers

Questions on faults in the comments will not be answered. Please use the contact us form instead.

TOP