Hoover Heat Pump Tumble Dryer DXH9A2DCE-80 / no response on pressing Start button
intermittent beeping, then no response beep when start button pressed. No error codes shown. for every 100 presses of the button 99 will fail to activate the machine. Tried the one touch actions via the wizard which is hit and miss, if it does energise it will be after a prolong delay and will shut off without fully completing the cycle.
- Published in
Hoover Vented Tumble Dryer VHV380-80 vented Motor runs when power applied And door closed
Hi,
I’m scratching my head with this.
With power applied and door closed the motor runs. No heat, no program, just motor running.
I. This state, pressing start, will start a program (heat is applied) but at the end, the motor continues to run.
Any ideas?
Cheers,
Stuart
- Published in
Hoover Tumble Dryer DXC9TCG-80 E21
Hi, I went through info on this error. Condenser and filter are clean and dry. When starting cycle it spins for 5 minutes and then stops and shows e21 error.
In those 5 minutes it doesn’t get any warmer (heater faulty?)
Looking to hearing from you.
Thank you and regards
- Published in
Hoover Tumble Dryer Vision Tech VTV590NC-80 Unit will not start
- Published in
Hoover Vented Tumble Dryer VHV781C-80 No Heat
Hi, Thank you for your guide, I have been through the various steps of the guide, but to say I am a little puzzled is an understatement. I tested all thermostats and had continuity over all of them. I tested the heater, (i think correctly) plus (by mistake) I managed to put my fingers on the heater element and got an electric shock (oh dear!) so I know I have power to the heater assembly. I just cant seem to find a reason for it not heating. On the PCB board, I noticed the relay you change in your board was slightly discoloured (looks like heat damage) and I could notice a spark from inside the relay after a couple of moments of operation.
Does this sound like a relay failure? If every other sensor is good? We had a power failure (unsure why, could have been overload, blew a 13A fuse, the dryer and washing machine are on the circuit) but washing machine is fine.
I can obviously get the part number off the relay if needed and solder the item, if this is the problem, where is the best place to get them?
Thanks,
Rob.
- Published in
Hoover Tumble dryer VTC591NC-80 Lights flashing no error code – timer dial won’t work on 150min – not fully drying
The timer dial turns to the 150min setting but won’t go on – all other settings work, however, once it has started spinning the display starts flashing and the clothes need to go on multiple times to dry. I’ve watched your great videos and tested the heater thermostats front and rear and the NTC sensor – all appear to be fine. Thanks in advance for any advice/help you may offer.
- Published in
Hoover Tumble Dryer ATDHY10A2TKEX-80 e21
hi i have this hoover hybrid heat pump dryer which is just over a year old and is now show e21.
i have cleaned all the filters and it still displays that error.
any help would be apricated
regards michael
- Published in
Hoover Vented Tumble Dryer VhV680C80 All the lights flash and it’s stops after about five minutes. Occasional faint smell of burning
Tumble dryer stops after about five minutes. All the lights flash and there can be a faint smell of burning. Checked vent and that seems ok unobstructed
- Published in
Bosch Tumble dryer WTA4007GB/01 Drum not turning
- Published in
Indesit Vented Tumble Dryer ISL60V It gets hot but only runs for a few minutes then stops the cycle?
It has been working fine and I replaced a thermostat in it 4 years ago, but it now ends the cycle too soon.
Thanks
- Published in