Hoover Candy Tumble dryer all lights flashing error fault code
Hoover Candy Tumble dryer all lights flashing error fault code
This video will explain how the error codes may be displayed on your Hoover or Candy tumble dryer and some Maytag, Helkama, Kelvinator, Otsein, Teka, Terzismo, Zerowatt models. We will explain what they might mean, there is a list of videos below that will help you with each individual repair showing you how to diagnose the faults how to replace the faulty parts . Always remember you can submit a comment or question below and we will try to point you in the right direction.
These fault codes for tumble dryers including both normally vented and condenser tumble dryers and may be used on other Candy made tumble dryer models.
These error codes do not relate to all tumble dryers as some have different circuit boards fitted. If you are unsure please ask
Before you start any investigation of the fault or even remove the lid of your tumble dryer please watch our videos and fully understand them in full and pay particular attention to the safety and information notices
Please remember to support our site by buying spare parts from our store and, if you decide we really heled you can always share the site with friends.
There are loads of video below to help you repair your tumble dryer condenser or vented and they will help you with all these makes Hoover or Candy tumble dryer and some Maytag, Helkama, Kelvinator, Otsein, Teka, Terzismo, Zerowatt models.
-
How a Condenser Tumble Dryer works
-
Tumble dryer not heating Hoover Candy diagnosing fault and repair
-
How to replace a tumble dryer belt Hoover or Candy
-
Hoover Candy Tumble dryer drum not turning and belt ok faulty capacitor
-
How a NTC Sensor works on a Tumble Dryer
-
Hoover Candy Tumble dryer all lights flashing error fault code
-
Hoover Candy tumble dryer empty water Indicator flashing, runs for a few seconds then stops
-
How to test and replace the heater, thermostats, Ntc sensor
-
How to service a Hoover Candy condenser tumble dryers
Hi I have just purchased a brand new candy tumble dryer. First time I try to use it and all the lights start flashing after a few minutes. Is this something I can fix myself or should I try to get a replacement machine? Many thanks
Hi hope you can help
I have a hoover vhc 580nc tumble dryer which no longer heats up, all lights flash after a while but no heat. I replaced the fuse and thermostat in the back after finding the 206 degree fuse had gone but it just keeps going so am now in need of help
I would appreciate any further advise
Kind regards
You need to check all the thermostats in the dryer there is usually one on the front also it is worth checking the relay on the circuit board
Appliances Engineer
Found the other stat and replaced now working perfectly thanks????
Where did you find the other one, was is on the left under the top board of the dryer?
Quentin where did you get the parts from for this please as i have the same tumble dryer with the same problem
I am struggling to find a follow on video – Candy GOV 580NC all lights flash, but it’s intermittent – where do I start troubleshooting? or do I just think life’s too short and replace it?
Hi i have a Hover VHV 680c-80 the one with no LCD panel. Recently it starts up fine and then after a few minutes all the lights flash on it times pauses for a few seconds and then flashes 8 times again. Just keeps on repeating this sequence. Do you know what this error code relates to.
i think you have e8 fault normally something to do with heater stats or relay
E8
Thermal fuse detected faulty
Check thermal fuse
Check wiring
Appliances Engineer
Do you know where I can purschase a fused thermostat for this exact appliance?
hoover candy Tumble dryer thermostat 206c Thermal Cut Out Fuse
Hiya we have an e15 fault on a hoover condenser dryer
N.3110069315120051 please you tell us how to sort this
Thank you!
E15 indicates Heater relay faulty.
This tutorial might help you.
https://how-to-repair.com/help/how-to-service-a-hoover-candy-condenser-tumble-dryers/
Hi we have a candy gcc591nd. All the lights flash with a beeping noise after a couple of seconds. How can I diagnose the fault. Drum turns but no heat.
Hi.
I have a candy GOV 580NC-80 vented dryer and when it is running all lights flash and it continuously beeps. I have tried to put it into the fault diagnostic mode and it beeps 3 times.
DO you know what this is and what I need to do to fix it?
Regards
Steve
when you have a question please use our contact us page for 24 hour response https://how-to-repair.com/help/contact-us/
Appliances Engineer
Hi there I have a candy grando comfort condenser dryer it’s new and when I put it on all the lights flash please can you advise what the problem may be I don’t want to be buying new parts all ready for a new machine thanks
when you have a question please use our contact us page for 24 hour response https://how-to-repair.com/help/contact-us/
Appliances Engineer
Hi there I have a candy grando comfort condenser dryer GCC590NB it’s new and when I put it on all the lights flash please can you advise what the problem may be I don’t want to be buying new parts all ready for a new machine thanks
when you have a question please use our contact us page for 24 hour response https://how-to-repair.com/help/contact-us/
Appliances Engineer
I have a candy grand comfort sensor condenser dryer all lights are currently flashing on said dryer any ideas?
when you have a question please use our contact us page for 24 hour response https://how-to-repair.com/help/contact-us/
Appliances Engineer
Hi I have a candy tumble dryer all lights keep flashing can u tell me what’s up with it
when you have a question please use our contact us page for 24 hour response https://how-to-repair.com/help/contact-us/
Appliances Engineer
Hi I have a candy grand tumble dryer all lights keep flashing can u tell me
What’s up with it plz
when you have a question please use our contact us page for 24 hour response https://how-to-repair.com/help/contact-us/
Appliances Engineer
I have a hoover dyc8132bx 80 condesor dryer. Heats up for abou 5-10 minutes the goes cold and stays cold. After about 30-40 minutes it stops and get E08 code. I have changed the heater and the two stats on top of it and it hasn’t made any difference. Please can you advise on what to do next. Thanks.
Appliances Engineer
Hi Paul. Sorry but your response has no information? I have checked for blockages and all clear. Checked the 2 sensors on front of machine and seem to be okay. Ohmes of about 20-25 ish on Ntc sensor. Brand new heater with stats fired. Still have the problem. Thanks.
this then might be the relay https://how-to-repair.com/help/tumble-dryer-printed-circuit-board-heater-relay-faults/
Thanks Paul. Would this cause it to heat for first 5-10 minutes then stop heating? If I switch machine off for a bit then back on it will heat again for another 5-10 minutes then go cold. Thanks.
I have a hoover infinity sensor condenser dryer, model number VHC 68B-80, I have all the lights flashing and and. Ee ping going off and there is no heat when I open the door could you please help thank you
candy gcc 500nb-80 all lights flashing drum still turning but no heat what could this be
Condenser Dryer – Model No. VTC 5911NB – Product Code 31100715 All the lights are flashing and beeping at once
Hi Kate did you fix this problem and if so how as i have the same problem now.
candy gcv 581 nc
All flashing light error. drum turns on but after 5-10 mins starts bledping and all lights flash. Can you help diagnose please.
Thanks.
Hi,
I have a hoover VHC 68B dryer. All the lights flash on constantly. What fault could this be please? Thanks
Hi I have a hoover VHV 781C -80 Ser No. 3110039912380276 flashing an error code of E 08 .
please help