Hoover Heat Pump Tumble Dryer DXH9A2DCE-80 / no response on pressing Start button
intermittent beeping, then no response beep when start button pressed. No error codes shown. for every 100 presses of the button 99 will fail to activate the machine. Tried the one touch actions via the wizard which is hit and miss, if it does energise it will be after a prolong delay and will shut off without fully completing the cycle.
Cameron
I will try and help with your Hoover Heat Pump Tumble Dryer DXH9A2DCE-80 problem.
This could be a problem with the circuit board or problem with the plastic couplings between the facial panel and the circuit board as you will see in the exploded diagram below also if your door lock is not working correctly this would also stop the machine from starting
If you want to support the site please mark us to your favourites, also I would be grateful if you would subscribe to our social media channels as this really helps my site and keeps us going.
YouTube. http://www.youtube.com/user/howtorepair
Facebook. https://www.facebook.com/how.to.repair.appliances
And if we really helped you save money you can always click on the Buy Paul a Beer page
Common Hoover Heat Pump Tumble Dryer DXH9A2DCE-80 faults with links to the right repair guide
I have included a lot of videos in the links below on these tumble dryers to assist you in repairing your tumble dryer; I have also included an exploded diagram of your machine with all the parts that you need listed below that just click on the relevant and it will take you to a search result
- No heat
This is the most common fault on tumble dryers.
Vented dryers: this can be a fault with the thermostats, heater, or on some occasions, it might be the timer or the relay on the printed circuit board.
Condensor dryers: this might be any of the above but you also have a condenser plate that collects the water and then is either pumped to the collection tray or flows into a tank. Check pump unit and float switches.
Heat pump dryers: these are much more complicated they use a refrigeration prosses to heat the cloths and use the cooling side to condense the water for collection. Check compressor is running, check NTC sensors and check filters, and also that it has the right amount of refrigeration gas (normally only done by an engineer)
- Drum not turning
This will stop the dryer from drying. You may have to replace a faulty belt or in other cases, look at the motor, motor capacitor, or the jockey wheels. Again there are relays on printed circuit board types that can go faulty.
- Not starting
Whilst, not a common problem, you may have a faulty door switch, starter relay if fitted, or can be start button or PCB.
- Noisy Machine
This is usually caused by faulty bearings, jockey wheels or worn felt pads. The motor can get dust build up in the bearings, also the fan blades can distort in shape and make noise rubbing the housing.
- Water leaks.
This can be a simple as the water tank (in a condenser tumble dryer) has not been emptied, or not placed back into the housing correctly. The condenser plate can need cleaning. The pump unit might not be working. Or the ducting system can be clogged with fluff etc. See servicing tumble dryer.
- Tumble dryer reports a fault code or error code.
Error codes can be on the display or given in certain lights flashing sequences. Tumble dryer fault codes are not universal but may only point you or an engineer in the right direction they are not 100% accurate they are only that for guidance. Your owner’s manual may help you identify the problem and even suggest a fix. In other cases, you’ll need an engineer to trace the fault. Don’t be tempted to ignore a fault code, even if the dryer seems to be functioning normally. Some codes are ‘early warning signs’ and fixing the machine at an early stage could save you time and money in the long run.Contact us with the full model number and detailed description
-
Noisey Tumble dryers, Rear drum bearing on , Candy, Hoover, Iberna, Kelvinator, tumble dryers
-
Tumble dryer not heating Hoover Candy diagnosing fault and repair
-
How to replace a tumble dryer belt Hoover or Candy
-
Hoover Candy Tumble dryer drum not turning and belt ok faulty capacitor
-
Hoover Candy Tumble dryer all lights flashing error fault code
-
How to service a Hoover Candy condenser tumble dryers
-
Hoover Candy tumble dryer empty water Indicator flashing, runs for a few seconds then stops
Match your part for Hoover Heat Pump Tumble Dryer DXH9A2DCE-80 and use reference number in list below and click on the link to your part
Reference | Part Number | Description |
---|---|---|
10 | 40009129 | Timer/select. knob |
31b | 40011129 | Control panel with Sensor |
48 | 40010677 | R/H side frame |
48a | 40010678 | L/H side frame |
49 | 40004597 | Top rear frame |
49g | 41041380 | Trade mark plate |
51 | 40004601 | Work top |
60 | 40009040 | Hinge |
63 | 40006231 | Door glass |
67 | 40010996 | Door with trim |
77 | 40008312 | Rear panel |
77 | 40012015 | Rear panel |
79 | 40002885 | Foot |
82 | 40009192 | Door panel |
88 | 40008589 | Front panel |
131a | 92470020 | Hose clip |
152 | 40010249 | Switch assy |
153 | 28375043 | Pressure switch |
156 | 41039164 | Capacitor 7 MF |
157 | 40011151 | Harness |
161 | 40005021 | Pump |
164 | 91200489 | Anti jamming filter radio |
171 | 40008346 | Main motor |
202 | 40009125 | Drum |
205 | 40006362 | Drum shaft assy |
218 | 03210179 | Bearing |
219 | 21446068 | Bolt |
229 | 24721202 | Circlip |
230 | 40004306 | Bearing clamp |
271 | 40005393 | Door gasket |
280 | 40009775 | Hose clip |
292 | 40001012 | Drive belt |
318b | 49039414 | Electronic control PCB - NFC -Programmed |
318c | 49041618 | Electronic NFC pcb - Not programmed |
440a | 46004464 | Scroll seal |
441 | 40006774 | Cover |
442a | 40006726 | Rear fan |
461h | 41014595 | drying probe seal |
491c | 91200201 | Mains cable x UK |
494 | 40010248 | Red window |
520 | 40006928 | Door coupler |
607 | 40006220 | Pin for hinge |
631 | 40006586 | Stopper |
643a | 41041381 | Handle plate - profile |
671 | 03610428 | Washer |
690 | 40006246 | Rear sealing felt |
690a | 40006778 | Rear cover seal |
697 | 40006724 | Heater support disk |
706 | 40010750 | Front ring assembly |
707 | 40005584 | Filter for carter |
731a | 40006359 | Delivery pipe (Water delivery) |
731b | 40006360 | Flow pipe (Water drain) |
734 | 40006721 | Container |
735 | 40006722 | Cover |
745 | 40009144 | Kickplate assy |
748 | 03320032 | Tube |
754 | 40006728 | Ventilator |
756 | 23715194 | Spring |
757 | 40003315 | Gasket |
763d | 40006727 | Reservoir top cover |
764 | 40004815 | Gasket |
766 | 40009648 | Water container assy |
777 | 40004157 | Heater gasket |
797 | 40004610 | Beltightening pulley |
799 | 40001026 | Belt tighteningb spring |
804 | 40009167 | Hinge fixing upper bracke |
808 | 40006767 | Capacitor contain gasket |
819 | 40009121 | Drum scowel |
822 | 40010003 | Innerdoor assy |
826 | 40004091 | Door hook |
835 | 40004307 | Drum support wheels |
864a | 40006806 | Filter |
865 | 40006763 | Condenser |
866 | 40006764 | Evaporator |
867 | 40009515 | Compressor |
868 | 41043444 | Run capacitor |
870 | 41020195 | Screw |
871 | 40009678 | Terminal Compressor Kit |
872 | 40006807 | Capillary hose |
873 | 40008116 | Rear insulating |
874 | 40006731 | Sponge filter |
874b | 40006730 | Plastic frame for sponge filter |
874c | 40006911 | Sponge filter fixing Pin |
875 | 40006762 | Ring seal |
998a | 40011127 | Eeprom File NFC |
999 | 41045051 | Electrical diagram |
1004 | 40005153 | Flow restrictor |
1017 | 41022106 | NTC probe |
1017a | 41035594 | NTC probe |
1026 | 40007831 | Front felt |
1069 | 40006796 | Gasket |