Creda Condenser Tumble Dryer T620CW Not drying the clothes
The machine works and tumbles but is not drying the clothes. What can I check?
Mark Terry
I will try and help with your Creda Condenser Tumble Dryer T620CW problem.
If your dryer is not heating up, usually there are 3 main reasons that can cause it. The most common is the Thermostat has gone faulty and need replacing, next is the heating element gone open circuit and lastly a problem with the PCB where the relay for the heater as gone faulty. The thermostat and the heater element are easy to replace. The relay on the PCB requires soldiering skills and sourcing of the correct equivalent relay to drop in place of the faulty one.
Please see below for machine diagram and list of all spare parts for it.
If you want to support the site please mark us to your favourites, also I would be grateful if you would subscribe to our social media channels as this really helps my site and keeps us going.
YouTube. http://www.youtube.com/user/howtorepair
Facebook. https://www.facebook.com/how.to.repair.appliances
And if we really helped you save money you can always click on the Buy Paul a Beer page
Common Creda Condenser Tumble Dryer T620CW faults with links to the right repair guide
I have included a lot of videos in the links below on these tumble dryers to assist you in repairing your tumble dryer; I have also included an exploded diagram of your machine with all the parts that you need listed below that just click on the relevant and it will take you to a search result
- No heat
This is the most common fault on tumble dryers.
Vented dryers: this can be a fault with the thermostats, heater, or on some occasions, it might be the timer or the relay on the printed circuit board.
Condensor dryers: this might be any of the above but you also have a condenser plate that collects the water and then is either pumped to the collection tray or flows into a tank. Check pump unit and float switches.
Heat pump dryers: these are much more complicated they use a refrigeration prosses to heat the cloths and use the cooling side to condense the water for collection. Check compressor is running, check NTC sensors and check filters, and also that it has the right amount of refrigeration gas (normally only done by an engineer)
- Drum not turning
This will stop the dryer from drying. You may have to replace a faulty belt or in other cases, look at the motor, motor capacitor, or the jockey wheels. Again there are relays on printed circuit board types that can go faulty.
- Not starting
Whilst, not a common problem, you may have a faulty door switch, starter relay if fitted, or can be start button or PCB.
- Noisy Machine
This is usually caused by faulty bearings, jockey wheels or worn felt pads. The motor can get dust build up in the bearings, also the fan blades can distort in shape and make noise rubbing the housing.
- Water leaks.
This can be a simple as the water tank (in a condenser tumble dryer) has not been emptied, or not placed back into the housing correctly. The condenser plate can need cleaning. The pump unit might not be working. Or the ducting system can be clogged with fluff etc. See servicing tumble dryer.
- Tumble dryer reports a fault code or error code.
Error codes can be on the display or given in certain lights flashing sequences. Tumble dryer fault codes are not universal but may only point you or an engineer in the right direction they are not 100% accurate they are only that for guidance. Your owner’s manual may help you identify the problem and even suggest a fix. In other cases, you’ll need an engineer to trace the fault. Don’t be tempted to ignore a fault code, even if the dryer seems to be functioning normally. Some codes are ‘early warning signs’ and fixing the machine at an early stage could save you time and money in the long run.Contact us with the full model number and detailed description
-
Hotpoint Indesit Tumble dryer not heating Replacing element
-
Tumble dryer noisy Hotpoint
-
How to replace tumble dryer belt on Hotpoint, Indesit, Ariston, Creda & Proline
-
Hotpoint Creda tumble dryer how to fit front felt bearing. Part 1
-
Error fault codes for Ariston, Hotpoint Indesit, Scholtes washing machines
-
Condenser Tumble Dryer how to replace the pump unit.
-
How to service a Condenser Tumble Dryer pump unit.
-
How to replace a Tumble Dryer fixed drum Riveted Drum shaft
Match your part for Creda Condenser Tumble Dryer T620CW and use reference number in list below and click on the link to your part
Reference | Part Number | Description |
---|---|---|
101 | C00095494 | PUSH ON FIX |
101 | C00207094 | CONSOLE T622CW |
103 | C00206139 | TIMER KNOB |
103 | C00195542 | COMPRESSION RING (FOR TIMER KNOB) |
107 | C00095496 | OPTION BUTTON |
109 | 1602414 | NEON LENS |
111 | C00095500 | Tumble Dryer Heat Switch |
112 | C00112121 | START SWITCH (TD) |
113 | C00095504 | M4X10 SCREW |
113 | C00207243 | TIMER KIT |
117 | C00095505 | NEON |
118 | C00095964 | NEON HOLDER |
122 | C00095506 | TOP COVER BRKT LH |
123 | C00095507 | TOP COVER BRKT RH |
124 | C00122256 | SCREW |
125 | C00206241 | TOP COVER |
125 | C00230333 | 8X1/2 PHILLIPS ROHS COMPLIANT |
301 | C00207255 | DOOR AND LINER KIT |
302 | C00095513 | CONDEN.TO DOOR SEAL |
302 | C00095787 | NO6X1/2CSK HD SCREW |
302 | C00095512 | DOOR LINER |
303 | C00095514 | DOOR LATCH EMZ (TD) |
303 | C00095789 | SCREW NO8 X1/2 |
304 | C00095515 | DR LATCH BLANK SIR. |
305 | C00095516 | BUSH |
306 | C00165923 | MICRSWTCH OP PIECE |
307 | C00095517 | Tumble Dryer Fluff And Lint Filter |
308 | C00095518 | DOOR SPACER |
309 | C00095519 | PLUG (WHITE) SIROCCO |
310 | C00206128 | Tumble Dryer Plinth Cover |
311 | C00095521 | AIR INLET SEAL SIR. |
311 | C00122256 | SCREW |
311 | C00206549 | FRONT PANEL WHITE |
312 | C00257618 | Tumble Dryer Door Catch & Latch Kit |
313 | C00095524 | CABLE CLIP |
314 | C00095525 | PEG LOCATING |
315 | C00095504 | M4X10 SCREW |
315 | C00095526 | HINGE DOOR UPPER |
316 | C00095504 | M4X10 SCREW |
316 | C00095527 | HINGE DOOR LOWER |
317 | C00095528 | DR CATCH BLANK SIROC |
318 | C00095529 | DOOR SEAL |
320 | C00095530 | RELAY (TD) |
322 | C00096379 | MICROSWITCH |
322 | C00096587 | ADJUSTING NUT |
322 | C00095785 | MICRO SW AND BRKT |
323 | C00205892 | M/SW |
323 | C00122256 | SCREW |
323 | C00095785 | MICRO SW AND BRKT |
326 | C00095532 | DOOR OPENING SPRING |
330 | C00095533 | FRONT SUPP ASSY SIR. |
330 | C00095789 | SCREW NO8 X1/2 |
331 | C00095534 | FRONT BEARING PAD |
332 | C00095789 | SCREW NO8 X1/2 |
332 | C00096382 | SIDE STRUT |
332 | C00095535 | SIDE STRUT |
333 | C00250645 | NO 6 RECD FLANGE |
333 | C00206306 | SUPPRESSOR |
334 | C00209085 | TERMINAL BLOCK ELKAY |
334 | C00149557 | SCREW ZN 6X3/8 |
335 | C00095540 | NO.6 PAN HD SCREW |
335 | C00095539 | STAT SHIELD |
335 | C00095536 | THERMOSTAT FRONT (TD ) 78C |
340 | 1701166 | SIDE PANEL WHITE |
340 | C00095542 | SIDE PNL SEAL STRIP |
340 | C00122256 | SCREW |
501 | C00095546 | DRUM ASSY |
502 | C00095547 | WATER DIVERS. STRIP |
502 | C00122256 | SCREW |
502 | C00095548 | REAR PANEL |
502 | C00230333 | 8X1/2 PHILLIPS ROHS COMPLIANT |
503 | C00113862 | DRUM REAR BEARING SQUARE SHAPE |
504 | C00142631 | DRUM SHAFT COLLAR |
505 | C00095551 | Tumble Dryer Drive Pin |
506 | C00199479 | Tumble Dryer Drum Earth Strip |
507 | C00095553 | REAR BEARING COVER METAL |
508 | C00206400 | MAINS CABLE AND PLUG |
508 | C00380932 | MAINS CABLE AND PLUG 1.8M BLACK |
509 | C00095557 | CABLE CLAMP SCREW |
509 | C00095556 | CABLE CLAMP/GROMMET |
510 | C00113823 | REAR SEAL 26MM |
511 | C00095561 | HEATER COVER KIT |
511 | C00095564 | HEATER COVER SEAL |
512 | C00095565 | Tumble Dryer Rear Bearing Fixing Bracket |
520 | C00095566 | Tumble Dryer Thermostat Kit |
522 | C00095567 | Tumble Dryer Heating Element |
523 | C00095568 | REAR PANEL SUPPORT |
524 | C00095572 | M3 X 6 TAPTITE SCREW |
524 | C00095570 | HEAT BARRIER |
526 | C00095573 | CLIP |
527 | C00095574 | RECIRC IMPELLOR |
527 | C00095608 | MOTOR KIT 343 (TD) |
528 | C00095575 | FOAM WASHER |
530 | 1701147 | COND.HSING UNIT SIR. |
531 | C00095577 | Tumble Dryer Condenser Unit |
531 | C00095578 | CONDENSER SEAL SIROC |
541 | C00115748 | Washing Machine Drum Shaft |
542 | C00095583 | SCREW TORX T25 |
543 | C00095584 | BLANKING DISC |
544 | C00095585 | MAINS CON AND SUPPRE |
544 | C00250888 | SCREW |
600 | C00095587 | BASE ASSEMBLY |
601 | C00095588 | FOOT |
602 | C00296462 | VALVE AND SEAL KIT |
603 | C00205913 | CAP WATER CONT |
606 | C00111360 | WHEEL |
607 | C00095592 | WHEEL AXLE |
610 | C00095593 | CAP DRAIN |
610 | C00095594 | FLOAT CHAMBER & SW |
610 | C00122256 | SCREW |
611 | C00205873 | Tumble Dryer Microswitch With Lever |
612 | C00096370 | COOLING DUCT LOWER |
613 | C00095598 | INLET RING SIR. |
614 | C00095599 | COOLING IMPELLOR (TD ) |
614 | C00095608 | MOTOR KIT 343 (TD) |
615 | C00095573 | CLIP |
616 | C00096511 | FRAME |
617 | C00095601 | COOLING DUCT UPP SR. |
620 | C00095603 | MOTOR SUPPORT BRKT |
621 | C00096375 | CAPACITOR 7MFD |
622 | C00095605 | JOCKEY WHEEL SPRING |
623 | C00165972 | PULLEY WHEEL & ARM ( TD) |
624 | C00095606 | MOTOR SUPP BRKT SIR. |
625 | C00095611 | SCREW M5 T/TITE HEX |
625 | C00095608 | MOTOR KIT 343 (TD) |
625 | C00230362 | M5X10 HEX SCREW |
626 | C00095613 | Tumble Dryer Drive Belt |
630 | C00160795 | HANDBOOK T620CW |
999 | C00206966 | BRAILLE CONT T620CW |
999 | 1702245 | TROUBLE SHOOT GUIDE |
999 | C00145918 | ENERGY LABEL T620CW |
999 | C00220988 | MANUAL T620 630CW |
How do you get the top front panel off to replace a start button?
Thanks
Good Day. when I clean the inside of my Creda dryer T620cw, wires puled out of the timer unit. please help me with a wire diagram to reconnect them.
I appreciate your kindness.
Best regards
Coen