Heat pump tumble dryer – finding faults and error codes
it is very difficult sometimes to diagnose the problems with these heat pump tumble dryers.
I have included a video to show you the test mode sequence and also a PDF below which I managed to obtain.
but whenever you need parts for these dryers you will need to quote your model number and also the PCN number before we can do that you to the correct part
if you are still having trouble please contact us using your full model number including the product number for help from Paul
This is what came out of one machine i serviced potential fire hazard
You will be amazed at what you find
you should clean the filter every time
38 Responses to “Heat pump tumble dryer – finding faults and error codes”
hi,i have a john lewis heat pump tumble dryer that stops after a short period and goes back to the start
after entering the test mode it shows fault E32,i clear it but it comes back again .could you please help
me with this problem.regards richard
HELLO
AEG – model: T77689IH3 PNC: 916097503-00 DRYER
WHAT’S MEAN ERROR CODE E32 ON C8???
REEGARDS
jULEK
I have the AEG T865901H3 and the error code is EH0 !!! HELP!!!!
THANKS
Hi I wonder if you can help
I currently have an AEG dryer similar to the one in your video but not with heatpump it has an error code of E91 and I can’t clear it, the machine won’t do anything except shows the display
Thanks
Steve
Hi, My dryer ( AEG Mod T76280Ac Prod no. 91609686000) shows error code EH0 quite often. Sometimes while drying, sometimes while turning after finished cycle. The manual says to turn it off and on and sometimes i need to wait a few minutes but it becomes normal again and usable.
Any idea why this is happening?
Thank you
Dear Paul,
We have a John Lewis Tumble Dryer, Condenser with Heat Pump. It doesn’t seem to be heating up. Following your video on this exact same model I have tried to get it into diagnostics mode but it won’t go. Holding down the Start/Pause and leer side button when the machine is on brings up an error message of E00. Any idea what I could do try try and see what is wrong with the machine. The machine is JLTDH18 with a product number 916 097 425 00 and Type number TC09H6MHP. Regards Paul
Hello,
I purchased an Electrolux EDC2086PDW 5 months ago.
the machine will not begin any cycle.
I am receiving an “ERR” message every time i try to start a cycle.
The Start/Pause button is blinking yellow.
Help!
Sincerely
Mike
Bonjour how-2-repair.com
mon sèche linge electrolux edh3674pde défaut ‘eho’ :’ ( vous pouvez m’aider Merci , you can help me Thank you, ( :
re bonjour maintenant code Default EHE humidité résistance ou se trouve la résistance seche linge electrolux edh3674pde Merci .
Great YouTube site .. I have an AEG tumble dryer. Running fine until three days ago. A code EHO.
I moved the machine so that I could try a different power socket. When plugged into a new socket the machine runs for 1 or even 2 full cycles before showing the same EHO code. I unplug for 30 seconds to reset and the same code appears. Unless I plug into a fresh socket! Very strange. I have had 6 new full cycles from the machine by using 2 different plug sockets alternately. Any idea what the underlying issue is? A sensor? Any help welcome.
Hello
you have a video of a belt change in the dryer TC12H6BHP AEG
any help you can please.
thanks
What a brilliant video, needed to change the broken belt on a john lewis heat exchange tumble dryer and couldn’t find any info even from AEG.
Machine is now back together working for £20 and an hours work.
I’m only sorry i found this site after i got the part. Will be back when the next thing breaks…….
Thanks again
Mick.
I’m glad we could help please remember to support the website by shopping with us, and if we really helped you can always donate by pressing the Buy paul a Beer page
Hi, I have just used your video to dismantle my hoover dxc9dg-80 tumble drier as I have fault code e22. The video was brilliant however once cleaned and rebuilt it lasted 5 mins and e22 code back on. I couldn’t see a pump motor nor did the video show one. Is this code for the full tank switch or one of the 2 ntc switches?? I will purchase the parts from your site if I know what to buy. Many thanks
Enjoyed your video on heat pump dryers, thank you.
Can you confirm the type of refrigerant gas used in the new heat pump dryers please.
Many thanks
Mick Beasley
I’m glad we could help please remember to support the website by shopping with us, and if we really helped you can always donate by pressing the Buy paul a Beer page
I need meter checking heating temperature
We have a John Lewis JLTDC01 condenser heat pump tumble dryer which keeps getting an error message E50. could you please tell what this means and how to correct the fault
Yeah me too, is it the Electric board controlling the motor? Which part should I purchase?
please use contact us page on parts
We have a John Lewis heat pump tumble dryer JLTDH18. We get an E32 error code which is conductometric sensing oscillation too low. It this worth repairing?
Questions on faults in the comments will not be answered. Please use the contact us form instead.
Hi, I have a John Lewis tumble dryer JLTDH18. The hinge on the door broke off so I bought a new part and replaced the door. Ever since then I am getting an ERR message when I turn the tumble dryer on and it just won’t start at all. I have unplugged the tumble dryer but this hasn’t helped.
Do you have any suggestions what this error message might be due to please?
Thank you!
Apologies, I posted this in comments instead of on the contact form.
Electrolux dryer EDH3498RDE stops after 2/3 of process with E20
after powering Off/On it’s working till complete
B13-6B pump on the rear and level sensor is ok
Google’s and Your’s err list doesn’t contain explanation of E20 🙁
p.s.
inside of dryer looks identical as in https://www.youtube.com/watch?v=hEf9YByHjc4
juts my has digital front panel
I have an AEG 59840 which has died completely with nothing appearing on the screen. Have checked the fuse in the plug which seems ok. Any suggestions?