NEW REPAIR GUIDES

FORGOT YOUR DETAILS?

AAH, WAIT, I REMEMBER NOW!

Beko washing machine wmb 7, 8, 9 Series diagnostic & test mode

by / Tuesday, 10 May 2016 / Published in Washing machines, Water Systems & Valves

How to enter test mode on Beko wmb 7, 8, 9 Series washing machines diagnostic & test mode to repair faults and test errors

Beko Diagnostic

 Important notice on Beko 

Before entering test mode please be aware that you are not meant to leave the washing machine Unattended. There is a chance the machine can overfill when testing the water valves or the Machine could overheat when testing the heater. Also when entering the test mode make sure the drum is empty as not to cause damage when on spin mode:

This video can be used on all these makes

WMB81431LW, WMB71231B, WMB61631W, WM5141W, WM5141S, WMB71422S, WMP601W, WMP541W, WMB81241LS, WML72S, WASH814DW, WMC6100W, WMB61021W, WMB71642S, WMB61431W, WMC6140W, WMB71021W, WMB61631S, WMB81241LB, WML72B, WMP652W, WMP631S, WM74135W, WMB61221S, WMB71231S, WM74155LW, WM74155LS, WMB61431S, WMB51221W, WM622W, WMB61431B, WMD61W, WMB51221S, WMP501S, WMB61221W, WM7355S, WMB81221LS, WMC6100S, WMB81241LW, WML72WXC, WMC6120W, WMB91242LB, WML15105D, WM5100W, WME8227W, WMB71442W, WM85135LW, WME7227W, WME7247W, WM5100S, WMC62W, WM6123W, WME7267W, WMC61W, WM6103W, WM6123S, WME7227S, WM6167W, WME8227S, WM5121W, WM6111W, WMP621W, WM612W, WM6355W, WME7247S, WMC61S, WM5121S, WM6167S, WME7267S, WM7335W, WME8227B, WMB91242LC, WMI71641, WMI7462, WMI71441, WMB71231W, WME7227B

Test Mode Sequence

If you have problems with the drum not turning or spinning. Then check the carbon brushes in the motor first and test the motor separately before running this Diagnostic sequence as you could do damage to the PCB.

 

To enter test mode.

 It is advisable that washing machine be switched off or at least 5 minutes prior to entering test mode

With the machine switched off shut the door and turn the dial to the 12 o'clock position. Now press and hold down the start/pause button and press the on/off on, while holding the start/pause button down for 3 seconds until the display shows a number or error code.

  Now that you've entered the Diagnostic / test mode, remember every time you press the start/pause button this will be one advance the program to a new test.

  • 1: All the the display or led’s will flash to check that they are working and door will now be locked.
  • 2: Drum does a clockwise rotation.
  • 3: Drum rotates anticlockwise rotation 
  • 4: Goes into spin mode on clockwise rotation make sure there are no clothes in machine before performing this test as washer will spin at its fastest rpm. 
  • 5: right hand water valve check
  • 6: left hand water valve check
  • 7: both water valve are now activated and all 3 compartments will have water flowing in. 
  • 6: This is the full wash and heat test. Machine will start to fill to the correct water level and continue to heat and wash.
  • 7: the machine will empty. the pump should drain the water away.
  • 8:After it has finished turn the machine off and on this will go back to normal mode.

 

entering test mode one beko washing machines

Tap symbol showing as fault

Beko washing machine error Diagnostic fault codes

Turn dial to 12 o'clock position

Beko washing machine E08 Error code

Error code showing fault

beko washing machine fault codes and error codes

Display will flash when in test mode




Tagged under: , ,

134 Responses to “Beko washing machine wmb 7, 8, 9 Series diagnostic & test mode”

« Older Comments
Newer Comments »
  1. Steve says : Reply
    September 2, 2017 at 8:46 am

    Hi there,

    Having an issue with my Beko WMB 81241LW. It seems to be stuck in a cycle and won’t progress. ive done the self test and the only code the display is showing is 1518. During self test it performs steps 1 & 2 fine then it just wont progress any further and is making a slight buzzing noise. Any help appreciated!

  2. Tracey says : Reply
    October 5, 2017 at 6:27 am

    I’ve had code F13
    Then 04 06 on beko WM 95135 LB
    I’ve tried doing the self diagnostic test. My washer skips the spin part but does all the rest.
    When I turn it on normally to try and test it starts to fill and then drains and just keeps doing this, doesn’t go any further, any ideas before expensive repair from beko

  3. JOE says : Reply
    November 25, 2017 at 7:05 pm

    Washing machine not working fault no E11 ON SCREEN

  4. sandr says : Reply
    January 12, 2018 at 2:55 pm

    boa tarde eu tenho uma maquina de lavar BEKO WMB 91242LC o código de erro e E18 o que poderei fazer ja tentei impar o codigo mas nao faz nada obrigado

  5. sandra says : Reply
    January 12, 2018 at 3:02 pm

    boa tarde eu tenho uma maquina de lavar BEKO WMB 91242LC o código de erro e E18 o que podes fazer mais tentei com o mais fácil de usar.

    nao consigo fazer o reset obrigado

  6. Rene says : Reply
    February 14, 2018 at 10:37 am

    Hi there I have problem with my beko washing machine wmb91442lw xl9 the problem that it’s not spinning I’ve done diagnostic test mode on it everything works please can you give some advise thank you.

  7. Rachel Robson says : Reply
    March 30, 2018 at 10:53 am

    My Beko washing machine comes up with error 0428. What does that mean?

  8. Daryn says : Reply
    April 15, 2018 at 10:27 am

    My machine keeps showing E–. What does this mean. It does not give a number just two lines after the E. I find if I rotate the settings to the right to cottons I get this error, but if I rotate to the left all the way round to the same cottons setting then it shows the timer and allows the wash. It is so strange that the direction I turn the dial has different results.

    I have had the machine for approx 4 years and it never used to do this. It only started over the last week.

    If is the same for any wash, just does not like clockwise for some reason.

  9. Eddie Cappleman says : Reply
    June 12, 2018 at 2:51 pm

    The machine seems to be stuck in a quick wash program. The test starts with the notice E18.
    ?hat fault is this and how can I fix it please?

  10. Michelle Allan says : Reply
    June 19, 2018 at 7:33 pm

    I need.to change the motot

  11. Carla says : Reply
    July 11, 2018 at 8:04 am

    My Beko WM71641 built in, front loading washing machine is working but leaks towards the end of the cycle. I have twice run an empty cleaning cycle to clear the pipes but the machine still leaks. I have drained the water out of the machine and found nothing in the water. Any advice as to how to best approach the problem. My son should be able to follow any videos – or would you recommend I call an appliance repair technician.

  12. Clint says : Reply
    July 27, 2018 at 12:18 pm

    I have a wm74135w beko how do I enter the diagnostics as no tutorial seems to cover this model

  13. Bo says : Reply
    August 28, 2018 at 5:43 pm

    Beko xl9 Start light is flashing but no padlock shows, can open door.
    Programme is stuck on 800 spin, 40 degrees and 1:15
    Pressing start and on at the same time gives error code F02
    Displays changes to spin 1880 (too many) and every other function light is on but nothing happens
    Please help?
    Thank you

  14. Paul Gould says : Reply
    September 1, 2018 at 3:24 pm

    I have a Beko WMB 81241 LW which shows a fault code E10. What is this please?
    Hoping you can help please.
    Many thanks. Paul.

  15. Kirsty says : Reply
    September 16, 2018 at 5:06 pm

    My machoe shows error EO2 what does this mean and is it fixable

  16. mukhtar says : Reply
    September 25, 2018 at 7:56 am

    i have becc washing machine type WMB60821 M NOT DRAINING THE WATER I TESTED THE PUMP OUT SIDE IT IS OK

  17. mukhtar says : Reply
    September 25, 2018 at 7:59 am

    i have BEKO Washing machine type WMB60821 M NOT DRAINING THE WATER I TESTED THE PUMP OUT SIDE IT IS OK

  18. Morshed says : Reply
    November 11, 2018 at 5:24 pm

    My beko wmb 71041 7kg can not start bring too 1st.when I sylect jinse wash 1000 spin and 70 digri temperature then I can play. But it’s machine play oviesly but it’s not running..

  19. Piotr says : Reply
    November 26, 2018 at 10:33 pm

    To read the error code you can also hold button 1. and 3. under the display while the machine is turned on. It doesn’t clear the error code, but only displays it. Works for Beko WMB 71242

  20. E KHAN says : Reply
    December 4, 2018 at 4:38 pm

    I have beko wmb81431lw washing machine. Its heater element was dead, i have changed it to new, but heaters are not getting the power, i tried another pc board, then i changed the pressure switch, but its still the same, lastly i changed the inter lock but no power coming to heater element. Please let me know, what els to do ?

« Older Comments
Newer Comments »
24h technical help answers

Questions on faults in the comments will not be answered. Please use the contact us form instead.





 
TOP